Contact experts in ANSYS to get answers
7,113 views 4,162 posts
Questions related to ANSYS
I have seen a lot of discussions here at ResearchGate and YouTube about the one-way speed of light and two-way speed of light. Can we measure the one-way speed of light with different relative...
01 December 2023 3,631 6 View
what should i do to increse the specific capacitance ?
01 December 2023 5,838 2 View
Is it possible to connect the inverter directly to the solar panel output and can a power inverter damage a solar panel, or vice versa?
23 November 2023 7,587 0 View
Is GP considered now unuseful as an automatic programming technique in the existing of ChatGPT?
21 November 2023 2,823 5 View
We consider cases of compressible and incompressible flows.
18 November 2023 3,425 5 View
can any one say how to create a revolute joint when we are using ls dyna in apdl platform.As we can not use MPC184 elemnt as thsi element does not support LS DYna
18 November 2023 418 0 View
Material: Ceramics Method: Nanoindentation, Berkovich indenter It is not a single case, the abnormal condition occurs especially when creep time exceeds 20s.
14 November 2023 6,246 1 View
Dear All, Biotechnologists from The area of Biotechnology. Currently I am serving as HoD in Department of Biotechnology, IMSEC, New Delhi NCR. Is there any person who can help me for two or three...
09 November 2023 2,896 4 View
i am performing explicit dynamic analysis of bearing in apdl lsdyna .can anyone share job file in apdl lsdyna
09 November 2023 7,790 0 View
i am performing explicit dynamic analysis of bearing in apdl
09 November 2023 4,367 0 View
I am working on modal analysis, there I am getting my first mode at around 800Hz for rotor, I am bit confused to which external frequency should I compare this natural frequency, while max...
02 November 2023 4,613 0 View
Hello everybody, I could not simulate wind speed fluctuation by assigning turbulence intensity (TI). I simulate the fluid-structure interaction by using STAR-CCM+ and Abaqus, and I simulate the...
02 November 2023 1,387 4 View
Hello everyone, I've been experimenting with GPU acceleration in OpenFOAM, but I've encountered challenges while trying to utilize packages like RapidCFD and AMGX. I'm seeking guidance on this...
02 November 2023 5,462 0 View
Does anyone have the full version of this article? If so please let me know, thanks. S. Hedayatrasa, O. Fink, and M. Kersemans, “Vibrational NDT with under-sampled data through physics-informed...
30 October 2023 4,875 1 View
The question was posed by Dr. Ali A. Al-allaq, professor of biomechanics in the Department of Biomedical Engineering - University of Technology.
24 October 2023 2,955 3 View
Dear all, I wanted to change the model equation in Sentaurus TCAD. For this purpose, I need to create a physical model interface (pmi) for the same. I am writing to ask for help in this...
19 October 2023 8,926 0 View
I am working to simulate about inverter for an electric car in the CST Studio Suite. when I input the value 400 Vdc for the battery/source, the value of the output voltage is 17 Vac. For your...
19 October 2023 5,540 12 View
Hello guys. I am working on the strength of composite pipes under pressure & I have written a VUMAT subroutine to be able to use 3D Hashin criteria. But unfortunately my Hashin criteria...
13 October 2023 7,061 0 View
i figure out the chart to design filter is 1-define filter function base are your need 2- define s parameters from filter function 3- define coupling coefficients from S parameters 4- optimize...
10 October 2023 6,193 0 View
Which characterization technique confirms the formation of metal organic frame work. My XRD pattern shows crystalline nature and the card number matches with literature. Is there any other...
07 October 2023 1,434 6 View
Permittivity and loss tangent of resin
06 October 2023 9,481 0 View
I was doing the compression tests on previously thermomechanically deformed pure titanium. The samples were uniaxially compressed in room temperature. The samples were cylindrical, and their...
05 October 2023 6,941 1 View
I made a piping model in ANSYS APDL, where I tried to input the gravity load with ACEL command. However, analysis results became implausible, where the stress was 1100 MPa, and when I did not...
05 October 2023 2,313 4 View
i am getting positive grating having a magnitude of around 0.01 db before resonant frequency. how to suppress these?
05 October 2023 5,933 5 View