Contact experts in ANSYS to get answers
7,313 views 4,162 posts
Questions related to ANSYS
Dear fellow researchers, I am trying to simulate the temperature variation during a laser sintering of some metal powder. Material properties (density and conductivity) depend on temperature. I...
04 October 2023 1,877 2 View
Comparing diesel electric propulsion and diesel engine propulsion. Which is more preferable for offshore duties?
30 September 2023 6,903 0 View
Required to understand how to solve potential flow around a ship hull.
30 September 2023 7,057 0 View
I want to design a solar inverter where do I start designing a solar inverter and which solar inverter should I design On-grade off-grade or hybrid inverter and what is the difference between...
29 September 2023 589 4 View
How to find out / calculate the absolute humidity of the air entering the solar dryer at the point of adiabatic saturation (%) for finding out Pick-up Efficiency? Reference 1. Fudholi, Ahmad,...
28 September 2023 5,410 2 View
The figure below contains some information otherwise it could involve more assumptions.
28 September 2023 5,804 1 View
Hello Everyone, I am presently working on a hollow cylindrical shaft assembled in to another cylindrical shaft. The torque is transferred between these shafts through a one way sprag freewheel...
25 September 2023 9,013 0 View
I know this resistor is to prevent the circuit from saturating (caused by offset voltage and input bias current). Who can tell me more details about this resistor?
22 September 2023 2,387 4 View
Experimental here i mean purely laboratory experimental trial , e.g A sensor is designed in a laboratory and the functionality verified using artificial sample . what risk of bias tool can be used...
18 September 2023 1,132 1 View
I conducted pipe stress analysis using CAESAR II. And now I am trying to create similar analysis but in this case I use ANSYS APDL. I find a problem while creating the boundary conditions, where...
12 September 2023 6,223 6 View
Does anyone have a data analysis software setup to share with me?
12 September 2023 3,634 4 View
how to calculate magnetic anisotropy from Ms and Hc. Could someone provide me with an exercise?
11 September 2023 3,926 2 View
Assuming the system is linear and FRF of this system is obtained by modal analysis, is it possible that FRF could be non-linear? And how can I know the FRF is linear or not by just checking the...
10 September 2023 4,684 3 View
At what bases we fix the specification values in device modeling of TCAD simulation tool. how do you know these specification values (i.e., doping concentration values, channel length and gate...
10 September 2023 7,403 2 View
What are the different forms of water in the atmosphere taking into consideration the process of evaporation condensation and precipitation?
09 September 2023 8,657 0 View
Hi everyone, I tested a traditional 2-1-1 MLM based on the Mplys syntax example of Preacher (see https://www.statmodel.com/download/Preacher.pdf for more info). I specified for standardized...
08 September 2023 2,935 1 View
I need to calculate the chemical diffusion of a species in a porous medium over a very long time (decades). I am at my first attempt with such research. Can anybody recommend what OF solver could...
07 September 2023 3,816 0 View
I am trying to optimize coil parameters in an attempt to model EMF generated in a coil placed closer to a current carrying conductor using Ansys Maxwell. I used a soild hollow cylinder as the coil...
04 September 2023 1,086 0 View
These standards are for testing Compression samples in fiberglass, and my question is when to use each.
31 August 2023 7,875 0 View
These standards are for testing tensile samples in fiberglass, and my question is when to use each.
31 August 2023 5,543 2 View
I am trying to do elastic property calculation in QE, with ibrav=8 using thermo_pw. But getting an error shown below. task # 14 from initialize_elastic_cons : error # 1...
30 August 2023 4,015 6 View
Currently, I looking for the information about the hot topic membrane modification by using graphene oxide. Because I believe that graphene oxide have a good properties and easy to modify in membrane.
27 August 2023 343 3 View
What is the current and practical role of occupational therapists in interpfoessional universal design teams?
17 August 2023 2,078 1 View
Sir, Why this problem coming in iteration? what actually mean? Some time it ends with few iterations after that it will become normal.
16 August 2023 4,450 0 View