Why the creep displacement decreases as time increases ?

14 November 2023 1 6K Report

Material: Ceramics

Method: Nanoindentation, Berkovich indenter

It is not a single case, the abnormal condition occurs especially when creep time exceeds 20s.

We would need many more information before answering you, starting from your diagram. Several factors could explain what you observe.

Badges
Science topic

More Zhidong Zhang's questions See All

Do experts have journals in the field of artificial intelligence and big data that are not indexed by SCI or EI?

05 August 2024 8,836 2 View

Are there any good simple systems or platforms to recommend?

In order to show people the beauty of control and enhance enthusiasm for learning control theories, are there any good simple systems or platforms to recommend?

05 August 2024 10,034 1 View

State of art in natural disasters?

Are increasing the costs of disasters in the affected countries.

01 August 2024 1,794 2 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

The complex interactions between oral microbiota and oral mucosal immunoregulation: implications for oral health and disease development?

This research question explores the complex interactions between oral microbes and oral mucosal immune regulation. The diversity and function of oral microbes have important impacts on oral health...

09 July 2024 7,883 0 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

A small question about the principle of lasers…?

Given the energy level diagram of a ruby laser shown in the right figure, where \( R_{02} \) is the pumping rate, and \( \tau_2 \) and \( \tau_1 \) are the lifetimes of levels \( n_2 \) and \( n_1...

23 June 2024 4,855 0 View

Can the matter wave theory which suggests that when matter waves resonate be used to solve HTS ?

Can the matter wave theory, which suggests that when matter waves resonate, the energy input from the outside is minimal, be used to solve all superconductivity problems? The matter wave theory,...

17 June 2024 7,957 0 View

How do I link researchgate with my pubmed publications?

I moved to a different institute and changed my email address. Somehow I lost the list of my publications. Is there a way to link to my PubMed publication list?

17 June 2024 5,312 2 View

There is any relationship between critical temperature of superconductor and the atomic weight & radius?

till now, there are many superconductors. Is there any relationship between critical temperature of superconductor and the atomic weight & radius? Now the isotope effect is one relationship...

12 June 2024 1,908 3 View

Can you suggest reliable procedures to get displacements from accelerations in frequency domain ?

I have identified many solutions. I need suggestion from somebody with application experience of this topic to identify the most reliable and robust procedure.

21 July 2024 3,465 5 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

How to use stress and displacement results from 1st stationary simulation as initial conditions for 2nd eigenfrequency simulation in COMSOL?

Dear All, I am trying to define the dispersion curves of a periodic unit cell in COMSOL Multiphysics with prescribed displacements. I am using two separate studies: - Study 1: Stationary, with...

13 July 2024 7,855 1 View

Abaqus不收敛，警告里面出现下列问题，需要更改哪个地方？?

The system matrix has 172 negative eigenvalues. Displacement increment for contact is too big. Displacement increment for contact is too big. The strain increment has exceeded fifty times the...

05 July 2024 3,839 2 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View

What is the difference between creep deformation and stress relaxation ?

I understand the basic definition for both. I found a literature to describe both of them. In the paper, they states: If a stress is applied to a concrete body, the body experiences an elastic...

19 June 2024 525 3 View

Difference between creep deformation and stress relaxation deformation ?

I understand the basic definitions of creep and pressure relaxation. However, I am confused about the exact difference between them. See attached photo. Because a compression force is applied,...

17 June 2024 5,344 2 View

What is the the target displacement for a retrofitted model outside US conditions (preferably Indian conditions)?

Dear Members of ResearchGate, I hope you are doing well. I have been retrofitting using the ASCE 41 2017 standard. In it, I have two basic doubts. 1. The target displacement as per clause...

13 June 2024 2,773 0 View