Contact experts in ANSYS to get answers
6,198 views 3,910 posts
Questions related to ANSYS
I investigate the bio effect of CeO2
01 November 2021 5,838 2 View
Hello, I am a researcher at Aachen, Germany. I was facing some problems in my research to rerun my simulation in ANSYS 2021R2. I have a turbine which is heated with heat mats which have already...
27 October 2021 8,018 3 View
Please suggest to me some high-quality articles for finding outlet temperature of Parabolic Trough Collector (PTC) by using ANSYS modeling with nanofluids.
25 October 2021 5,671 8 View
LAMMPS software tutorials, workshop and study materials
21 October 2021 1,728 3 View
Hi everyone, I want to know how to calculate the total contact pressure between two surfaces in ansys workbench. I have used the contact tool and found the maximum, minimum, and average values for...
16 October 2021 716 3 View
As a part of my thesis I am designing Finned pack heat exchangers for cooling/condensing warm air with water. I am not getting the exact procedure for it. I am reffering multiple research papers...
12 October 2021 3,483 7 View
I need the relevant legislation on social work/ benefits for the disabled people for a comparative analysis accross EU Member States
11 October 2021 6,352 10 View
What are the best technologies used to desalinate water on a large scale using solar energy, and how practical are these technologies? knowing that the source water is not marine water, but...
08 October 2021 3,436 12 View
In shell element, Is it possible to give temperature gradient through thickness in ANSYS?
08 October 2021 8,830 0 View
I'm working on mechanical APDL, modeling plate with attached resonators. I have attached spring(COMBIN14) and mass (MASS21) with the plate but it is not getting integrated. Please help me to solve...
07 October 2021 4,092 0 View
I want to find the resonance and anti-resonance frequencies of an ultrasonic transducer by analyzing its impedance. so I need to buy a impedance analyzer or spectrum analyzer or something like...
27 September 2021 8,953 5 View
I have solved a 3D structure of a protein with a ligand which seems to sit in a VERY strained conformation. I would like to quantify it by directly comparing conformational energy profile of...
24 September 2021 6,148 1 View
How to obtain young's modulus and poisson's ratio in ansys for a cellular structures?
21 September 2021 975 5 View
I need to establish a macro code of ANSYS to estimate the fatigue life of a part of structure and report the results to MATLAB, so that in MATLAB the sufficiency of the results is checked and if...
20 September 2021 4,337 3 View
I am doing simulation of my structure . when i enter the reference pressure using command pref, it shows the PREFOR COMMAND is obsolete as i am using apdl 2021 R1 ,
20 September 2021 9,666 1 View
Can you calculate the compression yield strength of the material given that you know tension yield strength and other properties of the material?
20 September 2021 8,745 3 View
Many models such as Mohr-Coulomb, Hoek-Brown model, etc. are available in the software.
18 September 2021 4,785 12 View
Dear all, I'm doing simulation using ANSYS 19.0 , The meshing always fails with the following error. "WARNING: License server lost for 55 minutes. Please save your work. License server will time...
16 September 2021 8,985 2 View
Hello dear colleagues, I couldn't figure out what are the required material properties to perform fatigue simulation using ANSYS SMART. What should I add to predefined structural steel to proceed...
06 September 2021 4,661 2 View
If zirconium oxychloride octahydrate is used as a precursor and Urea is used as a surface modifier, what should be the appropriate oven and calcination temperature for the zirconium oxychloride...
03 September 2021 5,150 4 View
Hi, I am trying to simulate two differents PCMs in FLUENT. I am wondering how can two set of operating densities (boussinesq densities) can be defined in operating conditions. Both PCMs have...
31 August 2021 3,406 2 View
Hello fluent users, I am working on Discrete Phase Modeling (DPM) on ANSYS and I am encountering one problem. It would be appreciated if you could help. I am using surface type injection from the...
31 August 2021 4,673 3 View
Hello Everyone, In stead of searching on each publisher or journal websites, I concern if we have a website address or a platform where we can use keywords and search all special issues with its...
31 August 2021 5,555 7 View
Analysis using simulation software (Ansys/Solidwork) to determine the stress deflection and vibration condition on the unit.
29 August 2021 3,610 6 View