Contact experts in ANSYS to get answers
4,937 views 3,535 posts
Questions related to ANSYS
I am trying to apply a load, say 100N downwards in the y-direction on a node, but for some reason, Ansys APDL is showing me the following 2 warnings: - The NODAL LOAD label of is not part of the...
05 August 2021 244 4 View
Hi,I want to perform an analysis using cohesive zone model in ANSYS,the model is shown in the following picture. I want insert interface elements between two materials (the purple material and...
03 August 2021 3,096 1 View
I am trying to simulate response of structure with TLD using ANSYS APDL. I mesh the fluid volume and tanker so that they can have coincident nodes, merge the nodes, flagged on FSI for the...
01 August 2021 9,224 2 View
Hello, I have been trying to model the flow over a hollow cylinder (diameter = 24 mm) on ANSYS Fluent. Now most publications I come upon seems to work in a much lower Reynolds number range (below...
01 August 2021 1,712 3 View
I'm working on the simulation of thermal behavior of Ionanofluids, which is an ionic liquid-based-fluid in which nanoparticles were suspended to enhance the thermal performance. Multiple...
30 July 2021 6,358 2 View
hello all i simulated a geometry in ansys cfx, i want define thermal conductivity that is function of three variables,these variables are in an excel file in each time step, so ansys should read...
29 July 2021 6,144 3 View
For conformal Mesh In design modeller we make our all bodies to "form a new part" and the meshing is done conformal. For using space claim how to "form a new part" for multiple bodies for the...
27 July 2021 2,746 3 View
Can someone help me in modelling a nonlinear spring by defining a set of equations. The spring should obey the force-displacement behavior as per the equations
26 July 2021 4,922 2 View
Especially, in case of compressible flows with shocks and expansion and compression waves, is it a compulsion to go for FMG initialization?
24 July 2021 4,489 1 View
Hello, I am trying to account for amplitude damping of acoustic vibration of a polymer disc, using Ansys software. I am currently using Harmonic Acoustics module in Ansys, which seems to be the...
23 July 2021 2,949 1 View
I performed transient structural analysis on a shaft geometry as a result I got the amount of thermal deformations. shaft geometry has different diameters on the surface, how to calculate the...
23 July 2021 6,079 3 View
Hi, Do anyone know how to add a custom (Chemical as well as physical properties, such as, viscosity, density, ratio of solution, etc.) fluid type in ANSYS?
22 July 2021 2,641 3 View
I have already made a 3D printed PLA part using FDM method and now I want to do a FEA(FEM) simulation of tensile test. Can anyone guide me which software I must chose and what is the procedure?
21 July 2021 418 3 View
Hello all thanks alot for your support I got up with a doubt , for simulation normally we use ansys or abacus of tensile testing . But when it come to polymers tensile testing which software...
20 July 2021 2,759 4 View
How can I measure phase difference between two points in a model in ANSYS HFSS? The model has one port that is excited by lumped port and I am using driven terminal. I want to know that is there...
19 July 2021 3,170 3 View
i started work in simulation on iron ore pot sintering process. in this how to give sinter mix( mixture of iron ore fines + coke breeze+ dolamite fines+ limestone fines) data in ansys fluent.
18 July 2021 5,248 1 View
Heloo All, I am doing simulation about archimedes screw turbine with ansys fluent. But, the continuity do not converge. It always increasing and become floating. The boundary condition is same...
16 July 2021 7,537 1 View
Working on analysis after assigning everything when I click on solve error popup saying invalid name selection how to resolve this can anyone help me out with this, please
14 July 2021 7,221 3 View
I have done a simulation of a linear synchronous motor. In transient mode, the motor torque characteristic is problematic. After many experiments, I still can not understand the problem of...
14 July 2021 4,371 2 View
I want to model resistance spot welding in ANSYS APDL. How to model heat generation, which happens in the highest amount at contact of two sheets? How to model electrical contact resistance or...
13 July 2021 1,772 3 View
I want to make a model for turbulence in Ansys. In the project a fan is used which is completely submerged in water. How to proceed in this situation ?
08 July 2021 8,304 3 View
Hello, this question is intended to those who have experience in designing electrical machines using ANSYS RMXprt software. I am not being able to select a material of my choice, when it comes to...
06 July 2021 6,183 3 View
I am trying to develop a goniolens and meshing it to the surface of the cornea of the eye model
06 July 2021 7,437 2 View
I am looking for a theoretical formulation of solid185. In particular, I want to understand which equations are implemented to build the stiffness matrix.
05 July 2021 8,537 3 View