Contact experts in ANSYS to get answers
5,619 views 3,910 posts
Questions related to ANSYS
Dear all, I wanted to change the model equation in Sentaurus TCAD. For this purpose, I need to create a physical model interface (pmi) for the same. I am writing to ask for help in this...
19 October 2023 8,802 0 View
I am working to simulate about inverter for an electric car in the CST Studio Suite. when I input the value 400 Vdc for the battery/source, the value of the output voltage is 17 Vac. For your...
19 October 2023 5,394 12 View
Hello guys. I am working on the strength of composite pipes under pressure & I have written a VUMAT subroutine to be able to use 3D Hashin criteria. But unfortunately my Hashin criteria...
13 October 2023 6,992 0 View
i figure out the chart to design filter is 1-define filter function base are your need 2- define s parameters from filter function 3- define coupling coefficients from S parameters 4- optimize...
10 October 2023 6,085 0 View
Which characterization technique confirms the formation of metal organic frame work. My XRD pattern shows crystalline nature and the card number matches with literature. Is there any other...
07 October 2023 1,274 6 View
Permittivity and loss tangent of resin
06 October 2023 9,339 0 View
I was doing the compression tests on previously thermomechanically deformed pure titanium. The samples were uniaxially compressed in room temperature. The samples were cylindrical, and their...
05 October 2023 6,806 1 View
I made a piping model in ANSYS APDL, where I tried to input the gravity load with ACEL command. However, analysis results became implausible, where the stress was 1100 MPa, and when I did not...
05 October 2023 2,096 4 View
Dear fellow researchers, I am trying to simulate the temperature variation during a laser sintering of some metal powder. Material properties (density and conductivity) depend on temperature. I...
04 October 2023 1,738 2 View
Comparing diesel electric propulsion and diesel engine propulsion. Which is more preferable for offshore duties?
30 September 2023 6,718 0 View
Required to understand how to solve potential flow around a ship hull.
30 September 2023 6,928 0 View
I want to design a solar inverter where do I start designing a solar inverter and which solar inverter should I design On-grade off-grade or hybrid inverter and what is the difference between...
29 September 2023 488 4 View
How to find out / calculate the absolute humidity of the air entering the solar dryer at the point of adiabatic saturation (%) for finding out Pick-up Efficiency? Reference 1. Fudholi, Ahmad,...
28 September 2023 5,279 2 View
The figure below contains some information otherwise it could involve more assumptions.
28 September 2023 5,646 1 View
I know this resistor is to prevent the circuit from saturating (caused by offset voltage and input bias current). Who can tell me more details about this resistor?
22 September 2023 2,286 4 View
Experimental here i mean purely laboratory experimental trial , e.g A sensor is designed in a laboratory and the functionality verified using artificial sample . what risk of bias tool can be used...
18 September 2023 966 1 View
I conducted pipe stress analysis using CAESAR II. And now I am trying to create similar analysis but in this case I use ANSYS APDL. I find a problem while creating the boundary conditions, where...
12 September 2023 6,061 6 View
Does anyone have a data analysis software setup to share with me?
12 September 2023 3,493 4 View
how to calculate magnetic anisotropy from Ms and Hc. Could someone provide me with an exercise?
11 September 2023 3,816 2 View
Assuming the system is linear and FRF of this system is obtained by modal analysis, is it possible that FRF could be non-linear? And how can I know the FRF is linear or not by just checking the...
10 September 2023 4,571 3 View
At what bases we fix the specification values in device modeling of TCAD simulation tool. how do you know these specification values (i.e., doping concentration values, channel length and gate...
10 September 2023 7,268 2 View
What are the different forms of water in the atmosphere taking into consideration the process of evaporation condensation and precipitation?
09 September 2023 8,524 0 View
Hi everyone, I tested a traditional 2-1-1 MLM based on the Mplys syntax example of Preacher (see https://www.statmodel.com/download/Preacher.pdf for more info). I specified for standardized...
08 September 2023 2,798 1 View
I need to calculate the chemical diffusion of a species in a porous medium over a very long time (decades). I am at my first attempt with such research. Can anybody recommend what OF solver could...
07 September 2023 3,706 0 View