Contact experts in ANSYS to get answers
6,313 views 3,910 posts
Questions related to ANSYS
Hello all thanks alot for your support I got up with a doubt , for simulation normally we use ansys or abacus of tensile testing . But when it come to polymers tensile testing which software...
20 July 2021 2,832 4 View
How can I measure phase difference between two points in a model in ANSYS HFSS? The model has one port that is excited by lumped port and I am using driven terminal. I want to know that is there...
19 July 2021 3,227 3 View
i started work in simulation on iron ore pot sintering process. in this how to give sinter mix( mixture of iron ore fines + coke breeze+ dolamite fines+ limestone fines) data in ansys fluent.
18 July 2021 5,357 1 View
Heloo All, I am doing simulation about archimedes screw turbine with ansys fluent. But, the continuity do not converge. It always increasing and become floating. The boundary condition is same...
16 July 2021 7,578 1 View
Working on analysis after assigning everything when I click on solve error popup saying invalid name selection how to resolve this can anyone help me out with this, please
14 July 2021 7,272 3 View
I have done a simulation of a linear synchronous motor. In transient mode, the motor torque characteristic is problematic. After many experiments, I still can not understand the problem of...
14 July 2021 4,435 2 View
I want to model resistance spot welding in ANSYS APDL. How to model heat generation, which happens in the highest amount at contact of two sheets? How to model electrical contact resistance or...
13 July 2021 1,913 3 View
Hello, I am tasked with designing a heat exchanger for pasteurizing beer. I am currently using the Log Mean Temperature Difference LMTD method to do the thermal analysis. I am struggling to find...
13 July 2021 164 5 View
I want to make a model for turbulence in Ansys. In the project a fan is used which is completely submerged in water. How to proceed in this situation ?
08 July 2021 8,360 3 View
Hello, this question is intended to those who have experience in designing electrical machines using ANSYS RMXprt software. I am not being able to select a material of my choice, when it comes to...
06 July 2021 6,224 3 View
I am trying to develop a goniolens and meshing it to the surface of the cornea of the eye model
06 July 2021 7,495 2 View
I am looking for a theoretical formulation of solid185. In particular, I want to understand which equations are implemented to build the stiffness matrix.
05 July 2021 8,587 3 View
User-Defined Function (UDF) in ANSYS Fluent to define the heat generation source of a Li-ion battery.
01 July 2021 7,284 3 View
I have generated the HOMO LUMO diagram for the complex but I am not able to get the contour value. Anyone can help to get that value for FMO?
22 June 2021 5,207 5 View
For my CFD simulation in ANSYS.. I need a basic understandable geometry of a membrane.... Where the process is for inorganic membrane separation of Carbon Dioxide from heated air or natural air
20 June 2021 5,391 1 View
Hi, I am performing a Fatigue analysis, I am referring to the ISO standards and they always stipulate to perform the fatigue tests at a precise frequency (20 Hz). I can't see in the fatigue tools...
20 June 2021 4,884 1 View
Hello, I am currently working on an axial pump. The original geometry didn't perform as well as I expected, so I plan to improve its performance. But all the ANSYS tools I tried either didn't work...
16 June 2021 1,154 2 View
I'm simulating a hypervelocity impact using SPH. I am using a particle size of 0.1mm with only 3512 SPH particles. My end time is 1.0 ms. Up until about 1.00 E-01 ms the simulation runs quite...
15 June 2021 2,273 0 View
If I have a rotor on two bearings, under what conditions should I use pre-stressed modal analysis and when should I run a rotordynamic analysis i.e. using the rotordynamics options in a modal...
10 June 2021 3,684 3 View
I was trying to calculate the radial distribution function by Lammps in between the moving particle (suppose an ion) and static particle ( suppose a wall). However, I couldn't find any result. I...
10 June 2021 6,772 2 View
Hi, I wanna ask for opinions/suggestions to reduce the percentage error between experimental and simulation results in the ANSYS workbench ( static structural). First, let me explain my...
09 June 2021 801 6 View
I am developing user material subroutines for anisotropic damage in orthotropic material in ANSYS APDL. So I would like to delete the elements when the damage of an element reaches a maximum value...
08 June 2021 7,210 2 View
I am a mechanical engineering student. I need a project on design using solidworks and analysis using anysis. Please share some basic solidworks and ansys project with me. I will try to do. Thank you.
08 June 2021 560 7 View
Fatigue analysis on ANSYS Mechanical APDL
03 June 2021 4,407 2 View