Review and cite AUTOMOTIVE ENGINEERING protocol, troubleshooting and other methodology information | Contact experts in AUTOMOTIVE ENGINEERING to get answers
2,538 views 465 posts
Questions related to Automotive Engineering
Development of two electrode electrodeposition system for electroplating components.
20 May 2016 4,890 1 View
I am doing a project on 5 parallel engine for wear analysis using 2-stroke engine. What is the suitable horsepower or cc of the engine should I use?
19 May 2016 9,763 6 View
exhaust gas re circulation is adding burned charge in some amount e with fresh charge to the cylinder s to minimize emission mainly NO .
12 May 2016 4,688 5 View
What are the new optional alternative fuels are there upon which one can do his research work..
10 May 2016 5,275 2 View
review paper or useful document
05 May 2016 4,892 2 View
For a vehicle driven at a particular gear, the gas pedal is ramp up from zero to 100 percent transiently within a very short period of time. How to model this condition using the pressure-crank...
20 April 2016 652 9 View
There are many problems associated with keyless car ignition.What are the ways the car can be turned off automatically when it is left in the on state unknowingly by the user.
17 April 2016 9,929 4 View
when stated in a vehicle brochure that the fuel consumption /100 KM is a certain value,is that at part load or full load or average between them?
17 April 2016 6,116 4 View
supercharger used in engine to increased both amount and pressure that charged to the cylinder to increase temperature and improve kind of combustion.
16 April 2016 4,501 9 View
I am interested in knowing if there are any journals or papers which discuss about the applications of Taguchi Loss function in Automotive Industry.
16 April 2016 1,487 1 View
During my study I observed that stresses are getting matched for shell and solid model of same geometry and loading conditions. But, strains are not even comparable, Is there any limitation of...
15 April 2016 8,140 3 View
Actually I have done research in passenger car tires fitted with ABS. Major properties were effected to carcass, tread and tread compound stiffness. But I didnt find any relevant papers on Truck...
12 April 2016 3,757 2 View
what is the cause behind this
10 April 2016 8,404 5 View
In practical machining by EDM. we always install dimensions of discharge openings on the machine in order to ensure the accuracy of processing.How can measure dimensions of discharge gap in EDM?
26 March 2016 7,244 4 View
the detection the vibration in diesel engine by using vibration sensor
26 March 2016 5,410 2 View
I'm studying about the backward facing step flow, suddenly, I'm wondering what is the result from backward facing step flow. I mean, is there problem due to BFS??? I saw somthing like lower...
26 March 2016 4,673 1 View
im working with vehicle detection and tracking .. i just want to know whether this issue can be handled here?
22 March 2016 5,537 3 View
How can coupling capacitor can create disturbance in vehicle electronic application and what is the impact to the micro controller ?
21 March 2016 647 5 View
I want to know how to find out the dynamic injection timing in a diesel engine and how it affects the calculation of delay period.
10 March 2016 9,578 3 View
Dear my friends I am looking for the best book about principal of internal combustion engine. please help me with best regards
07 March 2016 4,888 10 View
combustion takes place at low temprature so this should reduce thermal efficiency. misfiring can occur how is it eliminated
05 March 2016 7,530 4 View
Together with safety and performance, environmental impact reduction and cost containment throughout the complete life cycle of a vehicle are the major issues for today's automotive...
04 March 2016 4,002 9 View
I have found a few calculation prediction models for NOx and Soot(Carbon monoxide CO) formations that are applicable in my research. However, I have not similar models for prediction of emissions...
03 March 2016 8,278 3 View
Dear colleagues, I appreciate if you let me know your opinion and interpretation about roll Center, First of all I would like to know if you assume roll center as a fixed point or not?If yes why...
01 March 2016 5,460 1 View