Development of two electrode electrodeposition system for electroplating components.
The term "factor of safety" here is way off context - thus I really have to guess:
If it is about assuring a minimum-thickness of the plating, the factor of safety would be:
"How much more deposition do you have to "execute" - compared to the theoretical values."
Hope this helps
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I got these smeared bands quite often lately. We typically run the gel at 140V with a 10-12% gel and do a wet transfer at 220 mA for 1.5 hr in cold room. We also noticed some dirty spots/dots (see...
10 August 2024 7,480 3 View
I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?
08 August 2024 8,915 0 View
I am conducting my analysis using SPSS. I log transformed my data using In(X+1) as my data contain zero values. However, when I want to back transform the regression coefficients generated from my...
31 July 2024 7,860 3 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
PeptiCloud (www.pepticloud.com) is a bioinformatic platform that allows researchers to organize and share their data for their projects as well as collaborate with others in one place. Through...
28 July 2024 4,762 2 View
I created two potential gene expression cassettes (constitutive and inducible) for expression of a mutant PETase gene on PeptiCloud using the version tree feature, which allows users to create...
28 July 2024 7,559 1 View
Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...
24 July 2024 6,352 0 View
One problem w the BOD bottle type of OUR measurement is that it can only be used in a system that is not DO limited (typically assumed about 2 mg/l or more). If the system is running at low DO and...
01 July 2024 1,282 2 View
I am finalising my PhD and my word count is far greater than the faculty expect [80-100 K] Has anyone on here successfully submitted a PhD with a wordcount in excess of 120 K? Thanks in advance
27 June 2024 6,246 0 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Chemical Engineering /Food Engineering
20 July 2024 4,152 4 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I want to electrodeposit cobalt only leaving behind the nickel in the solution
15 July 2024 3,462 2 View