Kindly, how to prepare .25 mM sodium phosphate buffer solution at PH 5.8?

12 December 2018 0 3K Report

kindly, how to prepare .25 mM sodium phosphate buffer solution at PH = 5.8 ?

Badges
Science method

More Dyaa Barkat's questions See All

If i add a chemical solution to a fungus mycelia growm on PDA in plate. i want to make sure that my desired conc. of chemical would be fully absorbe?

If i add a chemical solution to a fungus mycelia growm on PDA in plate. i want to make sure that my desired conc. of chemical would be fully absorbed by the fungus cells but i also don’t want to...

03 April 2019 8,796 1 View

Which is better, making serial dilution for Ganoderma lucidum fungus in its PDB medium or in saline . and if saline is better , WHICH type of saline ?

kindly please, which is better, making serial dilution for Ganoderma lucidum fungus in its PDB medium or in saline . and if saline is better , WHICH type of saline ?

01 February 2019 1,883 4 View

Which acid or base should be added to adjust the PH of CYM media of the following composition: ( 1% w/v maltose, 2% w/v glucose, .2 % yeast......?

which acid or base should be added to adjust the PH of CYM media of the following composition: ( 1% w/v maltose, 2% w/v glucose, .2 % yeast extract, .2% tryptone, .05% MgSo4.7 H2O, .46%KH2PO4 )?

31 December 2018 6,084 2 View

Should i use the same fungus age in further indepenedent experiments or this doesn t matter?

should i use the same fungus age in further independent experiments or this doesn’t matter? i may use i an experiment a 7-day old fungus plate and in the next experiment i use a 5- day fungus...

11 December 2018 3,831 5 View

How to prepare .25 mM Phosphate buffer solution given that i need a final PH after adding to my media and i need final PH = 5.8?

I will add this phosphate buffer solution and I want to adjust the PH at 5.8

11 December 2018 7,330 0 View

Is centrifugation is reliable to get the dry weight of Ganoderma lucidum mycelia. if that the case which speed and time should i use?

is centrifugation is reliable to get the dry weight of Ganoderma lucidum fungus mycelia. if that the case which speed and time should i use? some friends recommended it because the filter paper...

11 December 2018 4,757 6 View

If a paper say in method that 100 ml of liquid media are put in 250 ml flask . and due to a limited space is it possible to put 50 ml in 125 ml flas?

if a paper say in method that 100 ml of liquid media are put in 250 ml flask as a media for Ganoderma lucidum fungus mycelial stage . and due to a limited space is it possible to put 50 ml in...

11 December 2018 1,962 2 View

Are ITS1 and ITS4 primers are ok for molecular work on ganoderma lucidum especially for ezymes and genes related to stress tolerance ?

10 November 2018 2,101 3 View

Why always stress treatments are pre-teratments not post- treatments?

why always stress treatments are pre-teratments not post- treatments?

01 January 1970 8,789 1 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

Sodium azide in immunohistochemistry?

Hello everyone, A collaborator sent us his protocol in order to be able to use his immunohistochemistry kits. But one step contains PBS + 0.3% H2O2 + 0.1% sodium azide. Knowing the dangerousness...

23 July 2024 6,314 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

How do I prepare a working stock solution of 14C sodium bicarbonate to get a final activity of 3uCi?

I need to make a stock solution for radioisotopic incubations of freshwater sediments to study dark primary productivity but I have some confusion as to how I calculate the concentration of 14C...

15 July 2024 5,898 0 View

How can EDTA be removed from already extracted DNA samples?

Our lab has extracted bacterial DNA samples using Qiagen DNeasy kit and eluted the samples in AE buffer. However, this buffer contains 0.5mM EDTA not suitable for downstream application. Any ideas...

13 July 2024 1,675 3 View