Simulink, developed by MathWorks, is a commercial tool for modeling, simulating and analyzing multidomain dynamic systems. Its primary interface... | Contact experts in Simulink to get answers
1,591 views 1,576 posts
Questions related to Simulink
Hi, I recently tried to set up an LPV system from local LTI systems. These LTI systems come as state-space systems with complex parameters. Apparently, this is not supported by Simulink as I...
15 November 2019 7,679 3 View
What is the interpretation of position control that requires torque signal conversion to linear form? How to implement that in MATLAB/SIMULINK?
11 November 2019 5,164 2 View
The MOSFET I have to simulate is a customized one, so I am not using predefined MOSFET blocks from the Simulink library. Also, I would like to start with the Level-I model. I am thinking of using...
11 November 2019 3,140 1 View
I have been trying to simulate my system whose Simulink schematic is attached, and also I have attached my results. The issue is, even though the wind is having sufficient generation, the power...
15 October 2019 7,882 13 View
Can I make the sampling time changeable during the simulation? For example, I want the sample time to be 0.0005 in the beginning and then change it to 0.00001 after 3 seconds.
11 October 2019 8,512 3 View
How to build a single pulse in MATLAB simulink instead of continuous pulse?
10 October 2019 4,441 2 View
Is there any open-source Software In Loop (SIL) test method available to test the network that was actually created in MATLAB. Anyone guide or give reference to use OPAL-RT testbed to integrate...
10 October 2019 1,232 1 View
10 October 2019 3,985 3 View
10 October 2019 5,738 14 View
Can anyone help me about implementing WirelessHART system using True time toolbox in matlab simulink, how to change communication system to WirelessHART instead of zigbee in true time tool box in...
10 October 2019 2,879 2 View
Hi all, I am working on an economic dispatch and unit commitment problem with plug-in electric vehicles (PEVs) integrated to a power system. I plan to test my model using the IEEE 24 bus RTS...
15 September 2019 2,295 4 View
I am designing an Electric vehicle fast charging station in Simulink. I am using a three level voltage source converter. Can anyone suggest me how to balance this converter by using suitable...
09 September 2019 2,286 3 View
Hallo, I am trying to simulate a fuel cell vehicle in Simulink, however i am confused about the controlling of Fuel cell with dcdc convertor. If anyone can help , I will be grateful. My problem...
09 September 2019 8,555 3 View
Hi community, Good day to you. This is my first time working on TCP/IP communication in Simulink. To understand better, I am using the examples 'TargetToTargetTCPServer' on my laptop and...
09 September 2019 8,936 3 View
the sampling frequency plays a critical role. If the sampling frequency for the controller is not choosen right, the controller does not work as intented. my question why mostly the sampling...
09 September 2019 9,102 2 View
How to implement a sliding mode controller in Matlab(Simulink) pls, give your valuable suggestion?
09 September 2019 4,188 5 View
Dear scholars, I want to control an HVAC system implemented in EnergyPlus using data and python programming. So I need to couple python and EnergyPlus. I'm using python instead of Matlab to...
09 September 2019 7,978 1 View
I have problem with simulation in Simulink, it cuts it after few microsecund due to algebric loop. Problem starts when i try to implement more than 2 surge arresters on overhead line. I' ve tried...
09 September 2019 2,708 1 View
to show power-sharing between ac side and the dc side we need an interlinking converter which will convert ac-dc and dc-ac, control strategy will be such that power-sharing takes place between ac...
09 September 2019 1,555 1 View
09 September 2019 3,768 3 View
please provide the matlab simulink model and code of optimization with ITAE objective function
29 August 2019 5,383 3 View
I want to model lazy eight maneuver by matlab simulink or AI. what shall I do???
22 August 2019 6,250 5 View
If I have a reinforced concrete slab with a thickness 1000 mm, containing openings 1.0x2.0m, 0.8x1.2m and 1.0x1.5m, what is the additional reinforcement to be added around the openings and its...
19 August 2019 9,677 4 View
To some extend I can understand theory of field oriented control of PMSM. From a text book i got a simulation diagram also. When i rigup it in matlab simulink and run I got some error. I...
08 August 2019 3,636 4 View