Simulink, developed by MathWorks, is a commercial tool for modeling, simulating and analyzing multidomain dynamic systems. Its primary interface... | Contact experts in Simulink to get answers
2,240 views 1,674 posts
Questions related to Simulink
Hi all, I am working on an economic dispatch and unit commitment problem with plug-in electric vehicles (PEVs) integrated to a power system. I plan to test my model using the IEEE 24 bus RTS...
15 September 2019 2,376 4 View
I am designing an Electric vehicle fast charging station in Simulink. I am using a three level voltage source converter. Can anyone suggest me how to balance this converter by using suitable...
09 September 2019 2,333 3 View
Hallo, I am trying to simulate a fuel cell vehicle in Simulink, however i am confused about the controlling of Fuel cell with dcdc convertor. If anyone can help , I will be grateful. My problem...
09 September 2019 8,609 3 View
Hi community, Good day to you. This is my first time working on TCP/IP communication in Simulink. To understand better, I am using the examples 'TargetToTargetTCPServer' on my laptop and...
09 September 2019 9,012 3 View
the sampling frequency plays a critical role. If the sampling frequency for the controller is not choosen right, the controller does not work as intented. my question why mostly the sampling...
09 September 2019 9,167 2 View
How to implement a sliding mode controller in Matlab(Simulink) pls, give your valuable suggestion?
09 September 2019 4,245 5 View
Dear scholars, I want to control an HVAC system implemented in EnergyPlus using data and python programming. So I need to couple python and EnergyPlus. I'm using python instead of Matlab to...
09 September 2019 8,045 1 View
I have problem with simulation in Simulink, it cuts it after few microsecund due to algebric loop. Problem starts when i try to implement more than 2 surge arresters on overhead line. I' ve tried...
09 September 2019 2,767 1 View
to show power-sharing between ac side and the dc side we need an interlinking converter which will convert ac-dc and dc-ac, control strategy will be such that power-sharing takes place between ac...
09 September 2019 1,630 1 View
09 September 2019 3,828 3 View
please provide the matlab simulink model and code of optimization with ITAE objective function
29 August 2019 5,422 3 View
I want to model lazy eight maneuver by matlab simulink or AI. what shall I do???
22 August 2019 6,350 5 View
If I have a reinforced concrete slab with a thickness 1000 mm, containing openings 1.0x2.0m, 0.8x1.2m and 1.0x1.5m, what is the additional reinforcement to be added around the openings and its...
19 August 2019 9,754 4 View
To some extend I can understand theory of field oriented control of PMSM. From a text book i got a simulation diagram also. When i rigup it in matlab simulink and run I got some error. I...
08 August 2019 3,702 4 View
08 August 2019 5,886 4 View
I want to implement Simulink model as shown in attached figure. But the problem is how to get the DSK6713 which is shown in the right-south corner of the figure? Which software is required ? I...
08 August 2019 3,580 4 View
To design control algorithm for 3 phase inveter with unbalanced load using Cascade control (Voltage - outer, Current -inner). And also which safety protection must be carried out for testing in...
08 August 2019 1,884 5 View
simply, I can put a PI block in simulink and specify gain and sampling time .. BUT this time I need to remove this block from simulink and put a function block, where inside, I can set Kp .. Ki.....
08 August 2019 7,491 5 View
I want to limit the current entering the battery and a load. How can I use a current limiter in MATLAB Simulink?
08 August 2019 8,697 6 View
How can i generate a continuous signal from my discrete data vector in Simulink (with a Matlab function)? suppose that you have raw data from sensor...
08 August 2019 903 6 View
Derivative of state '1' in block xxxxx/STATCOM/Controller/LPF' at time 0.0 is not finite. The simulation will be stopped. There may be a singularity in the solution. If not, try reducing the step...
08 August 2019 6,181 2 View
hello all, In Simulink : how can I create a single pulse of: amplitude = 1, width = 300 sec (for example) when ever the input changes from 0 to 1 (otherwise it equals 0) ? thanks
08 August 2019 7,512 4 View
I am doing an analysis on MPPT in PV by comparing the traditional method with an intelligent one. I am looking for a working circuit ( PV with Fuzzy control ) with FIS matrix files. which i can...
08 August 2019 670 6 View
04 August 2019 3,929 3 View