Simulink, developed by MathWorks, is a commercial tool for modeling, simulating and analyzing multidomain dynamic systems. Its primary interface... | Contact experts in Simulink to get answers
2,243 views 1,674 posts
Questions related to Simulink
I am doing my research on a communication system. I need a Simulink model with MIMO OFDM anyone of you could suggest me to find the total OFDM transmitter and OFDM receiver Simulink design model
22 December 2020 3,937 1 View
Please I have 4 groups of 8 sets of differential equations that I want to use for simulations. Each set has 8 differential equations to form a group. Each group is coupled with another group...
15 December 2020 8,579 10 View
Hi everyone iam facing a problem to give control signal for switches in design of PSFB converter in matlab simulink. Anybody's help will be appreciated.
15 December 2020 6,315 3 View
I have created a three-phase cascaded h-bridge inverter at Simulink with the SHE-PWM technique, and I want to test it in the DVR applications. How can I design a controller for that in the DVR...
14 December 2020 989 3 View
Hello everyone, I am trying to generate a faulty acceleration signal with SIMULINK. The inner ring of the bearing is fixed to the shaft. The bearing has 17 rolling elements. I was thinking of...
11 December 2020 4,401 4 View
Hello ! When tried to linearize the model for Bode plot in matlab getting the following error. In "frestimate(modelname,op,io,in)", it is required for each of the linearization input I/O...
09 December 2020 5,013 1 View
Hello everyone, I am trying to implement an algorithm to detect possible damage at a bearing. In order to test my algorithm, it would be helpful to generate faulty bearing acceleration signals?...
08 December 2020 1,728 3 View
How to calculate the inductance and resistance of a 'multi-winding transformer MATLAB/Simulink block'?
08 December 2020 8,449 3 View
I have noticed my battery SOC keep on increasing even before I close the switch between Constant current source and battery ! Any idea why this is happening ? Tried manually deleting the...
04 November 2020 9,519 9 View
I am working with a paper which have to renewable resource system PV and Flywheel (FESS). The system is built with MATLAB software, for PV system has been done with good results, but I am facing a...
31 October 2020 4,382 2 View
Hello dear colleagues and experts! When developing a model of a wind generator, I faced the problem of adjusting the PI controller for the pitch angle. I read a lot of articles, but the PI...
28 October 2020 9,546 10 View
Hi all I have been simulating a WPT system to check the S-parameters and efficiency of my selected parameters (L, R, k, M) on ADS. Now I would really like to do the simulation on Simulink to...
27 October 2020 6,325 5 View
Dear all, I have a set of I/O data. I estimated a transfer function based ( command: tfest) on this data in MATLAB. (I removed the trend from the data before it: command: detrend). Can I...
25 October 2020 1,943 5 View
Dealing with LLC resonant converter simulation and would like to plot the efficiency curve. How Can I do that ? eff = Pout/Pin ( Pout I can calculate from Output voltage and current but input...
19 October 2020 5,480 4 View
Hi everybody, I'm doing a project for my BoS thesis in Electronics Engineering. What I have to do is to control a quadcopter (of which I have the mathematical model, both linearized and non...
19 October 2020 8,719 6 View
to design massive MIMO with 64 antennas in transmitter side
13 October 2020 8,642 2 View
I have gone through some papers related to DTC for five phase induction motor. And trying to simulate the circuit with their specifications using Matlab/Simulink. But got stuck with feedback...
08 October 2020 1,311 2 View
I want to model, simulate and study the partial shading effects on the electrical characteristics of Series-Parallel, Brindge-Linked, Honey-Comb and Total-Cross-Tied PV array configurations under...
06 October 2020 6,956 0 View
Everyone knows matlab simulink, modelica and so on for simulation calculations. I want to make stand-alone app for kids with visual programming interface dor simulation different process and...
03 October 2020 3,709 3 View
I want to set the threshold of motor current. When the motor current reached to the limit, I want to control motor to rotate in other direction. I have to do this in Matlab Simulink. If anyone...
27 September 2020 1,701 2 View
I am working on a closed-loop system which has a PI controller. I have made a Simulink environment for the overall scenario but now I want to optimize the coefficients of the PI controller through...
24 September 2020 6,531 5 View
I want to implement below mentioned look up table in matlab simulink but i got error mentioning that ," Unable to perform assignment because the size of the left side is 2-by-3 and the size of the...
24 September 2020 9,684 3 View
Hi there, I'm trying to optimize an electric vehicle e structure (battery, motor, etc....), my battery model is on Simulink and the motor's is built using Ansys Maxwell I want to parallel optimize...
21 September 2020 3,597 4 View
I have a Simulink model and C code for a project. I need to cross verify by transforming c code to Simulink model. Can it be possible in Matlab or any other Source for the same.And too i tried...
09 September 2020 8,038 2 View