Simulink, developed by MathWorks, is a commercial tool for modeling, simulating and analyzing multidomain dynamic systems. Its primary interface... | Contact experts in Simulink to get answers
2,244 views 1,674 posts
Questions related to Simulink
Hello everyone,recently I have met some problems in my study.I want to achieve a multi-agent system in DC micro-grids,but I never used java so that I can't use Jade to achieve it. Can I only use...
08 September 2020 6,581 2 View
I am performing an optimization, where in a Simulink Model (involving Matlab function blocks and discrete event blocks amongst other typical blocks) block parameters are changes by an optimization...
18 August 2020 5,157 4 View
I have trained a fully connected model with two layers using pytorch framework, I would like to use the trained model in Matlab for possible deployment in target hardware.
10 August 2020 7,110 3 View
Dear All when simulating a feedback control system with Fuzzy controller in MATLAB Simulink for a tank level get this warning in run mode : ''input 2 expects a value in range [-4 4], but has a...
09 August 2020 4,810 8 View
I was trying to realize the simulation of the paper, namely Adaptive Synchronization of Reaction-Diffusion Neural Networks and Its Application. I used Simulink for simulation, but the...
06 August 2020 8,692 1 View
I am simulating PV behavior on Simulink under various shading conditions using the KYOCERA KC200GT PV module with dimensions 56.2 in. * 39.0 in. If I have a 5x5 PV array with uniform...
04 August 2020 2,323 4 View
Any recommended URL or idea , that explains how to read encoder via Arduino IDE and then use these readings in MATLAB simulation to be used as a feedback compared with the desired speed and...
27 July 2020 9,030 7 View
Hi everyone, I'm not sure what kinds of analysis models should be used for discrete percentages, here's an example: the data were the number of counts, and also the percentages of the...
24 July 2020 7,853 2 View
I am trying to make a Matlab/Simulink model of Mach-Zehnder EOM but I won't able to add a laser source in it and how to apply electrical data in terms of half-wave voltage to the one arm of EOM?
07 July 2020 1,836 17 View
How can we make the rating of a battery in MATLAB/Simulink to Amp-sec instead of Amp-hour? I have tried with reducing the factor of 3600 to 1 inside the battery block. Is this approach completely...
04 July 2020 4,369 4 View
Hi, I'm new to the Simulink and wondering if there is an existing model I can use to simulate the relation among input variables (like inlet air temperature\pressure\humidity), compressor speed,...
16 June 2020 5,575 3 View
Recently, I began to study the multi-agent control of dc microgrid based on distributed consensus algorithm.I try to use the Jade platform to communicate between agents in the system, which can...
16 June 2020 4,643 7 View
I'm trying to do some searches about islanding detection of synchronous generators connected on distribution lines. I would like to know if anybody could help me with some paper that shows how to...
14 June 2020 5,575 7 View
A basic diagram is attached which shows the design. Basically, it is a trolley, which will be moved up stairs, using conveyor belt system at its base. I am trying to find the required power for...
14 June 2020 5,583 0 View
I'm trying to run a Simulink model and at the same time receiving and processing data in a Matlab script, and sending the result into Simulink to change the behavior of the model. Is there any way...
04 June 2020 9,995 10 View
I've got Solar irradiance data and Temperature data for a month in 1 hour time intervals in a Excel sheet. I've modelled a Simulink block set to get the Output of a PV array. Unfortunately, I'm...
28 May 2020 3,360 5 View
Hi, i need a Matlab simulink model for PSO-fuzzy to track the maximum power point for a solar system Thank you [email protected]
22 May 2020 5,213 3 View
I have used hilbert filter on the current signal and i have to add two signals, one signal after hilbert filter and other signal before hilbert signal, however, i have used simple adder but i...
14 May 2020 7,649 7 View
Please recommend a tutorial set(pdf/book) for MATLAB Simulink for beginners?
09 May 2020 5,342 40 View
for example: for over head lines we can use pi section line or distributed paramters.I am working on the underground cable and in my system i want to add underground cable to get accurate results....
04 May 2020 3,472 3 View
Here's something to meditate on today: When your head tells you one thing and your hunches tell you another, go with your hunches. Your instinct knows things your head will never understand and...
30 April 2020 8,571 0 View
I'm currently working on peak shaving using Solar PV-battery system via matlab simulink. I'm looking for guidance me to get 3-phase battery dc/ac bi-directional converter simulink circuit....
28 April 2020 1,964 3 View
I uploaded more details and it is my first time to learn to convert manipulator equation to martice. (some are from wiki ,pages and some are from text book) Thank you very much because I really...
27 April 2020 9,898 0 View
I am running a simulation until steady state is achieved. At the end I would like to save the final states(as an array or structure with time) so that I can use these as the initial states for...
22 April 2020 8,055 10 View