Can anyone suggest how to find proper OFDM MIMO Simulink model ?

22 December 2020 1 4K Report

I am doing my research on a communication system. I need a Simulink model with MIMO OFDM anyone of you could suggest me to find the total OFDM transmitter and OFDM receiver Simulink design model

Md Ashad Alam

I hope It can help you

DOI: 10.26438/ijcse/v7i3.7275

Badges
Science topic

More Razzaq Shaik's questions See All

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View

Is there any analytical model to asses impact of rigid projectile on monolithic deformable plate?

I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...

08 January 2021 3,251 4 View

Why internal energy absorbed during impact is different when simulated with solid and shell elements using abaqus?

I am trying to simulate high velocity impact of rigid spherical projectile on a rectangular plate using Abaqus Dynamic Explicit. Particulars of Projectile Diameter : 12 mm Mass : 7.05g,...

04 January 2021 10,022 3 View

Which GC column is used for the analysis of essential oil/perfume samples ?

I have Agilent GC-MS and need to analysis essential oils which column will be applied for their analysis

30 December 2020 4,811 2 View

What are the challenges in Machine Learning to integrate it with Mobile Adhoc Network ?

What are the challenges in Machine Learning to integrate it with Mobile Adhoc Network

21 September 2020 3,881 5 View

How to calculate Poisson's ratio for sandwich panel?

I am simulating the compression test of the sandwich structure in Abaqus. How can I calculate? Please suggest me a method to overcome this problem. Thank you

05 July 2020 4,085 10 View

Question for SAS with two Factor?

I have experimented with two Factor: Factor A: Two iron sources and Factor B: two seasons with three blocks. When I run the SAS, the interaction not significant, but the combination of the...

18 May 2020 2,576 6 View

Can anyone send a Guidelines to write a systematic review in agriculture topic?

I need Guidelines to write a systematic review in agriculture topic.

24 March 2020 8,050 8 View

How to convert mg/L to mg/kg values in the measurement of plant tissue minerals analysis?

I analyzed the plant tissue minerals such as N,P,K by atomic absorption (AAS). I take 0.25g of dry sample and digested. Then filtered and complete the solution to 100ml. The final reading for N,...

23 February 2020 3,164 8 View

Which combining technique (MRC or SC) is better for Cooperative communication with Non-orthogonal multiple access technique?

I am using maximum ratio combing and selection combing techniques for C-NOMA. I want to compare the results for both techniques and also suggest me any other alternative combing techniques which...

27 January 2020 7,557 10 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View

Can we simulate light with matlab ?

Hi, I have to design a digital model of different types of lighting. Is it possible to simulate the lighting level from different sources (LED, incandescent, mainly fluorescence) with matlab...

28 January 2021 3,818 10 View

Algebraic Loop Problem in PV array Solution?

I am doing a project with PV array in Simulink. When I run small section of the total system i do not get an error. But when i integrate full system(my system model`s are completely okay) I get an...

18 January 2021 685 10 View

How to build aero engine fuel system online prognostics simulation model using Matlab, Simulink and Simscape?

17 January 2021 5,181 1 View

"The following block is not supported in Phasor simulation?

I am designing a control system for Hybrid renewable energy systems using Matlab/simulink/simscape, but currently having a problem. Whenever I run the simulation, I get the error shown below. "The...

12 January 2021 2,142 5 View

Steps for Hardware Implementation of Max Log MAP Decoder simulated in MATLAB?

How to implement max Log MAP algorithm turbo decoder on FPGA? Simulation is done on MATLAB. What are the next steps to be followed? Do I need to use HDL Coder feature in MATLAB? Is it needed to...

07 January 2021 4,405 4 View