Review and cite MACHINES protocol, troubleshooting and other methodology information | Contact experts in MACHINES to get answers
4,570 views 594 posts
Questions related to Machines
Currently, in the context of search and retrieval of any information resource, People, Places and Information resources are being connected, discoverable and mapped with one another in machine...
26 November 2018 3,320 2 View
Also tell about its range. Can it be more than 200 or 300?
23 November 2018 1,117 14 View
In statistic reference book ( An Introduction to Statistical Learning, ) is mentioned that this method use for sampling ,I saw at some blog that mentioned this methods as machine learning...
07 November 2018 4,310 2 View
Voltage is Potential energy so location of electron might be over the surface in high voltage
05 November 2018 7,822 1 View
Actually I am design a VFFS machine on solid works so I need the dimension design calculations of VFFS MACHINE
21 October 2018 4,619 1 View
we have all data of a 3.6MW DFIG, but we want to determine rated current and rate voltage of this machine.
18 October 2018 9,980 1 View
In simple self-replicating machines (exclusive of developmental automata), the structure of the description (machine genome) is very simple. For the von Neumann model, the description is...
11 October 2018 6,480 3 View
Knowing the kVp and mAs for an x-ray machine, I need to model it as a source in my Monte Carlo input model. I know how to use these inputs to calculate the average energy of the spectrum, but hope...
08 October 2018 6,568 9 View
It is necessary to understand the direction of applied research in the ergonomics of mining machines using the theory of fuzzy logic.
20 September 2018 5,881 3 View
Hi all..! Can anyone knows where is the high temperature wear test machine is available in India?
20 September 2018 8,357 4 View
If SMFC worked batch wise in anaerobic mode, how are we sure that CO2 was formed and not other gas like methane?
19 September 2018 6,900 3 View
We are trying to identify prospective biomass-based raw materials for designing and developing pellet production machines. Any help?
18 September 2018 5,254 3 View
physical variables that are taken into account when constructing this machines
18 September 2018 2,874 3 View
I have a project where I am trying to test the use of Ultrasound propagated through a TMS generated magnetic field. I was having trouble understanding what the TMS machine actually passed current...
18 September 2018 2,782 1 View
I was wondering if there are any general recommendations/guidlines to speedup the performance of Z3? P.s. I am using the C++ bindings. Best Regards, Rehab
17 September 2018 5,784 7 View
I am using the DSATools software to do a simulation of four generators eleven buses. Firstly, I suppose to do a simple simulation with single machine single line. However, I don't know how to use...
16 September 2018 5,700 1 View
Any suggestion on how to carry out a compression strength test on 50 mm cubes? We have comprehensive machine and Schmidt hammer, but neither of them suits tgese smaller samples as per the...
15 September 2018 4,054 1 View
I am designing Battery pack for a DC system. In order to find out the capacity required for the system, I need to calculate the energy requirement (Variable load, Idle condition). Since the...
11 September 2018 9,898 8 View
Just wondering if anyone here knows by chance how to install Octave in Fedora. I am going to post this in Fedora Forum as well, but sometimes the answers there are are too technical and assume...
11 September 2018 7,700 3 View
Washing machine drum vibration - rotating drum - equipment for measurement
07 September 2018 7,819 3 View
Grasscutter type of machine
04 September 2018 8,900 2 View
Our thickness range up to 1.5mm.is there machine or die problem to not get the uniform thickness or powder problem we are pressing manual and filling powder is also manual in die.tell me the...
01 September 2018 5,264 1 View
what is the for we not getting uniform in thickness and strength.is there powder problem or machine or die problem.give some die design and automatic filling designs.our pellet is in circle shape...
31 August 2018 6,162 3 View
Hi all, I'm working on a project regarding moisture content of gummies products. I try to dry the gummies inside a drying machine at a temperature of around 33 degree C. After two days, I checked...
30 August 2018 9,045 2 View