Contact experts in 3D to get answers
1,489 views 1,395 posts
Questions related to 3D
How to display pie diagram of analysis result of a sample taken from the field on 3d view (tin) in arcgis?
27 September 2021 8,595 3 View
i want to make an 3D model (like rail with sleeper supported on rigid base ), i want assume that there in no strain in the direction of rail (using plain strain condition), can i do this in abaqus...
24 September 2021 5,473 1 View
Please explain the boundary conditions for pile foundation analysis in PLAXIS 3D program
22 September 2021 1,483 0 View
For example, the results of a three-dimensional simulation are four-dimensional data (x,y,z,p). The first three are just spatial coordinates, and the last one is pressure. How could I plot those...
21 September 2021 806 8 View
explain your idea
21 September 2021 2,648 2 View
Hi everyone, I created a 2-bladed VAWT model. The dimension is the same as the turbine used in the experiment. I have run a 3D transient simulation via sliding mesh. The calculated torque from...
19 September 2021 4,372 3 View
Hi! I would love it if someone can explain how to read the vibrational frequency data listed in NIST website. For example, there are four vibrational modes (in cm-1) listed for Methane...
19 September 2021 8,699 2 View
Hello everybody! I'm having troubles with a previous established protocol for cells coculture in collagen on transwell for a 3D in vitro skin model. I prepared the collagen mix with 0.5M NaOH,...
17 September 2021 2,248 3 View
The surface roughness of same material at same location is different when calculated using 3D OSP (Ra = 0.55 microns) and AFM (Ra = 7.1 nm).
10 September 2021 4,195 4 View
Hi everyone, I hope you doing great. I already installed QE, and while I was doing some calculations I noticed the notion of K_points. After doing some research, this is what I got: In 1D, the...
09 September 2021 2,529 2 View
Hello I have to perform a localization of a underwater autonomous vehicle (UUV) and for that purpose have a couple of sensors available on board. I know that ultrasonic (Sonar) sensors perform...
09 September 2021 3,005 4 View
1. We have the geometry and shear strength parameters of the slide. 2. Can we add dipping layers in the slide body ? 3. Can we include structural discontinuities (Fault/Thrust) in the slide body...
07 September 2021 9,457 4 View
I'm one of the, I assume, many struggling with the lack of Matrigel in the market. For growing 3D organoids, is there any alternative that works? I work with swine and these are harder to culture...
30 August 2021 5,897 5 View
Hello, I normally stain 12-micron cryosections for pancreas tissue (looking at insulin and glucagon expression). I would like to try staining 50 micron sections for confocal microscopy. Do I...
28 August 2021 4,525 0 View
Dear All, I wonder if there exists any 3-dimensional representation of a spiral (e.g., prime number spiral)? Here is, what I mean: In 2D, a spiral is an ordinary object. E.g., a spiral of...
27 August 2021 7,337 2 View
I plan to conduct IF confocal microscopy of fixed and live cell experiments. I have used Poly -L- and -D- lysine (PDL). PDL lysine seems to work but I am still observing toxicity. Are there any...
26 August 2021 538 4 View
I'm trying to stain spheroids embedded in alginate- gelatin hydrogel using mitochondria probe (not Immunostaining). However, I'm getting very high noise and very low signal with this dye...
25 August 2021 253 6 View
I have a data set in 3D space which is recorded as X, Y and Z. I applied FPCA for X, Y and Z variations separately. Is there any possibility to apply FPCA to 3D data as once the means (X, Y,Z) as...
23 August 2021 5,910 1 View
Hello everyone, what softwares are best for making a 3D plot that can be used for publications. I am looking at paraview and origin. If anyone can put me through, I will appreciate that. Note: My...
23 August 2021 2,730 3 View
I want to model a moving concentrated force to simulate the moving wheel load on the pavement in a simplified way as shown in the attachment. So, is there any way to model the moving concentrated...
18 August 2021 2,932 3 View
after completing the batch processing of my data in pymca my 3D image has become 2D and splitted into half.how do i merge left half of the image into right half and bring it back to 3D? (image on...
17 August 2021 7,418 3 View
Hi everyone I have design a 2x14 array by using HFSS 3D module and then exported the designed as dxf format and imported it in HFSS layout. When I compare both results they are very much...
17 August 2021 7,593 3 View
i want to implement a network in which a single node can have two interface but uses one at a time : 1st for wifi 802.11 2nd for zigbee 802.15.4 is it possible to do so, please help
05 August 2021 8,549 3 View
I'm currently attempting a 3D FDTD simulation where I'm modeling a plasma as a dielectric tensor based off a frequency dependent Appleton Hartree dispersion relation. The inversion of the...
31 July 2021 4,568 3 View