Contact experts in 3D to get answers
1,133 views 1,031 posts
Questions related to 3D
What adapters are available for connecting 1 mm OD pulled glass capillary needles to a 1/16" OD PEEK tubing?
20 October 2021 3,317 1 View
It should have volume element. Can any one suggest how to proceed?
19 October 2021 7,001 3 View
GalaxyRefine is for refinement of single chain 3D structure. I normally use YASARA energy minimization to ensure stability of my predicted protein. Now if I want to use GalaxyRefine for energy...
19 October 2021 8,264 3 View
After performing docking for my hypothetical protein with ligand from PDB experimentally confirmed structure, do I need to validate my docking study. Do I need to redock the PDB ligand with PDB...
19 October 2021 9,987 8 View
Some researchers referred to (Machine compliance factor) as indicated in the following link Using a Correction Factor to Remove Machine Compliance in a ... However, this technique is valid for...
16 October 2021 1,900 4 View
Hello there I want to deposit a thin layer of copper on polyurethane foam. I should avoid the formation of Cu2O during the experiment. So what is the best pH for copper electroless plating solution?
16 October 2021 5,754 4 View
So I am working on 3D structure prediction for some proteins and need to validate the structure using amongst others a tool that does Ramachandran plot. Any ideas about possible tools?
14 October 2021 9,344 4 View
Hello all, I am working with a protein X for which we are running an ITC (Isothermal Titration Calorimetry) experiment with a ligand ATP. When we have performed the initial experimental...
14 October 2021 6,319 3 View
Dear all, I have a problem in culture of HDFs. Every time I seed them, they detach from the surface of the flask, or even they don't adhere at all. Consequently, precipitation occur without any...
13 October 2021 6,532 3 View
i am working on uncertainty analysis for the inversion results obtained by running least square inversion technique for my 2D ERT data sets. i want to ask how can i generate the synthetic ERT...
06 October 2021 7,073 5 View
Hello all, I have been trying to put nodes in specific locations in the mesh of a 3D solid body in ANSYS workbench, unfortunately without success. Does anyone know how can i do it? I've found...
30 September 2021 5,246 4 View
Dear all, Hope you are doing well, I have a 3D model in OpenSees consisting of Displacement-based fiber elements. I have defined element recorders for them to capture the forces and...
28 September 2021 168 1 View
I want to score disease symptoms across several genotypes grown in a greenhouse. Will RGB-D sensors be useful for this purpose?
28 September 2021 5,085 3 View
How to display pie diagram of analysis result of a sample taken from the field on 3d view (tin) in arcgis?
27 September 2021 8,563 3 View
i want to make an 3D model (like rail with sleeper supported on rigid base ), i want assume that there in no strain in the direction of rail (using plain strain condition), can i do this in abaqus...
24 September 2021 5,460 1 View
Please explain the boundary conditions for pile foundation analysis in PLAXIS 3D program
22 September 2021 1,466 0 View
For example, the results of a three-dimensional simulation are four-dimensional data (x,y,z,p). The first three are just spatial coordinates, and the last one is pressure. How could I plot those...
21 September 2021 790 8 View
Hi everyone, I created a 2-bladed VAWT model. The dimension is the same as the turbine used in the experiment. I have run a 3D transient simulation via sliding mesh. The calculated torque from...
19 September 2021 4,361 3 View
Hi! I would love it if someone can explain how to read the vibrational frequency data listed in NIST website. For example, there are four vibrational modes (in cm-1) listed for Methane...
19 September 2021 8,682 2 View
Hello everybody! I'm having troubles with a previous established protocol for cells coculture in collagen on transwell for a 3D in vitro skin model. I prepared the collagen mix with 0.5M NaOH,...
17 September 2021 2,236 3 View
The surface roughness of same material at same location is different when calculated using 3D OSP (Ra = 0.55 microns) and AFM (Ra = 7.1 nm).
10 September 2021 4,178 4 View
Hi everyone, I hope you doing great. I already installed QE, and while I was doing some calculations I noticed the notion of K_points. After doing some research, this is what I got: In 1D, the...
09 September 2021 2,512 2 View
1. We have the geometry and shear strength parameters of the slide. 2. Can we add dipping layers in the slide body ? 3. Can we include structural discontinuities (Fault/Thrust) in the slide body...
07 September 2021 9,444 4 View
I'm one of the, I assume, many struggling with the lack of Matrigel in the market. For growing 3D organoids, is there any alternative that works? I work with swine and these are harder to culture...
30 August 2021 5,871 5 View