Contact experts in 3D to get answers
1,339 views 1,395 posts
Questions related to 3D
spectroscopy and multiple reader
30 October 2021 3,461 5 View
I want to calculate spatiotemporal parameters using Xsens data; however, I'm new to Xsens and have no idea how to calculate these parameters using the Xsens .mvn file. I'd appreciate it if you...
29 October 2021 6,054 3 View
If the aerial vehicle like blimp or quadrotor is required to track the 3D position coordinates then how we will generate the reference trajectory for the vehicle? What will be the reference roll...
28 October 2021 4,086 3 View
I wanted to decrease the analysis time of a problem in Flac 3D. However, an error is coming like " Given timestep is greater than dynamic critical timestep!". Is there any possible way to solve...
28 October 2021 1,249 3 View
I have to 2 DEMs, one as a reference data and the other to be tested. I need to use the Z coordinate of both images to do RMSE calculation. I need the same points sample for both DEMs.
26 October 2021 2,963 5 View
Share novel interlacement of woven fabric and how the effect interlacement pattern on mechanical properties of the fabric.
25 October 2021 172 1 View
Any idea how to change the coordinates from xy coordinate system to 1-2 coordinate system as shown in plaxis manual?
25 October 2021 2,801 1 View
Hello. I've prepared Golgi-Cox slides of hippocampus and prefrontal cortex. I'm planning to analyze total dendritic spine density and density of several types of spines separately by Imaris...
21 October 2021 2,592 4 View
which software is easier to design 3D chemical structure
21 October 2021 7,648 6 View
Like minimizing the energy of a 3D predicted hypothetical protein should I need to minimize/ refine the ligand also for optimum molecular docking? Please help. Thanks ---Sunzid
20 October 2021 6,897 3 View
As you can see in the image attached to the question, there are some Radial Partitions one of the surfaces (Surface 2) of the lens. This is an illumination lens made by PMMA and its FWHM is 120...
20 October 2021 6,865 1 View
What adapters are available for connecting 1 mm OD pulled glass capillary needles to a 1/16" OD PEEK tubing?
20 October 2021 3,322 1 View
It should have volume element. Can any one suggest how to proceed?
19 October 2021 7,007 3 View
GalaxyRefine is for refinement of single chain 3D structure. I normally use YASARA energy minimization to ensure stability of my predicted protein. Now if I want to use GalaxyRefine for energy...
19 October 2021 8,279 3 View
After performing docking for my hypothetical protein with ligand from PDB experimentally confirmed structure, do I need to validate my docking study. Do I need to redock the PDB ligand with PDB...
19 October 2021 9,997 8 View
Some researchers referred to (Machine compliance factor) as indicated in the following link Using a Correction Factor to Remove Machine Compliance in a ... However, this technique is valid for...
16 October 2021 1,907 4 View
Hello there I want to deposit a thin layer of copper on polyurethane foam. I should avoid the formation of Cu2O during the experiment. So what is the best pH for copper electroless plating solution?
16 October 2021 5,757 4 View
So I am working on 3D structure prediction for some proteins and need to validate the structure using amongst others a tool that does Ramachandran plot. Any ideas about possible tools?
14 October 2021 9,363 4 View
Hello all, I am working with a protein X for which we are running an ITC (Isothermal Titration Calorimetry) experiment with a ligand ATP. When we have performed the initial experimental...
14 October 2021 6,335 3 View
Dear all, I have a problem in culture of HDFs. Every time I seed them, they detach from the surface of the flask, or even they don't adhere at all. Consequently, precipitation occur without any...
13 October 2021 6,544 3 View
i am working on uncertainty analysis for the inversion results obtained by running least square inversion technique for my 2D ERT data sets. i want to ask how can i generate the synthetic ERT...
06 October 2021 7,081 5 View
Hello all, I have been trying to put nodes in specific locations in the mesh of a 3D solid body in ANSYS workbench, unfortunately without success. Does anyone know how can i do it? I've found...
30 September 2021 5,253 4 View
Dear all, Hope you are doing well, I have a 3D model in OpenSees consisting of Displacement-based fiber elements. I have defined element recorders for them to capture the forces and...
28 September 2021 177 1 View
I want to score disease symptoms across several genotypes grown in a greenhouse. Will RGB-D sensors be useful for this purpose?
28 September 2021 5,092 3 View