Why do my MCFs not form monolayer?

Hello, I am looking for some expertise on culturing MCF7s. I purchased them from ATCC and I have been following all media and culture conditions. Media is EMEM with 10% FBS and 10ug/mL of...

27 February 2021 3,904 2 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Can we measure porosity of a composite by DSC (heat flow measurements)?

In the DSC conducted for A and B (image provided). B is a derivative of A. Can I conclude that the porosity of composite B is more than A, Since the heat flow is decreasing with increase in...

26 December 2020 9,104 3 View

Can I carry out LC-MS for AuNPs?

Will it be helpful to know the nature of stabilizers used in synthesis of curcumin (if it has polymerized or not). Any specific measures to be followed to carry out these kind of experiments?

15 December 2020 2,283 4 View

Why I am not getting UV absorbance peak of AuNPs?

I synthesized Au deposited on graphite electrochemically by using chronopotentiometry. How much ever I tried I couldn't get UV absorbance peak of AuNPs in any number of solutions I tried? But when...

20 October 2020 2,040 5 View

Can i use surfactant C-TAB in extraction and detection of the aminaphthalene sulfonates by HPLC technique?

In the detection of Aminonaphthalene sulfonates the quaternary ammonium salts like Tetrabutyl ammonium bromide ,Triethyl ammonium acetates are used so the C-TAB being an quarternary ammonium...

21 September 2020 9,636 1 View

How to fill the gap between two contigs?

Hi everyone, We have sequenced genome of data of a comparatively less studied species using Pacbio long read sequencer. Now after initial assembly we compared the contigs with previous version...

25 June 2020 3,442 3 View

Which motion analysis software can give me this functionality to create some sort of kinematic model?

25 October 2019 2,556 6 View

Automation in ansys with load location as parameter?

What is the best way (in a way that ansys runs each job sequentially without manual command) to solve several problems (say 1000+) with exact same geometry and other solution parameters but...

07 October 2019 2,073 3 View

What is the best method to measure conduction band offset of heterojunction?

Conduction band offset of a heterojunction is important for device performance.

20 July 2019 3,581 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View