What should i do after i calculate my cooling load how do i choose the components (compressor , condenser and evaporator ) based on my cooling load ?

02 April 2020 0 1K Report

Hello ,

i need to know how i can select the proper components of my refrigeration system after i find the cooling load required and cooling capacity

Badges
Science topic

More Ali Alshami's questions See All

Can we mark 'EFL Learners shifting from general digital to AI technologies' as technological transition?

After COVID-19 it has seen that EFL learners technological affiliation has raised. In addition, in the post-COVID period learners started to engage AI technologies like ChatGPT while learning...

08 August 2024 8,964 4 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,690 3 View

Does Anyone have expertise in in vitro transcription and RNA pull down assay?

I am currently working on LncRNA; to know the lncRNA-protein interactions I want to do RNA pull down assay, so I need to design primers with T7 promoter. I need assistance in this regard.

07 August 2024 6,622 1 View

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under op microscop?

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?

07 August 2024 2,132 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,291 2 View

How can I add own Henry coefficients in Aspen Plus?

Hi, i would like to simulate an absorption process in Aspen Plus. I want to use the NRTL model und would like to add some individual Henry coefficients. Is that possible and how?

05 August 2024 2,333 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Solvent recovery after extraction - Separation of Isopropanol + Water - how to do it best?

I want to make some yeast extractions with a protocol that uses Isopropanol and NaOH. So in the end i will have an azeotrope of Isopropanol and Water that comes from the cell and NaOH. Can you...

08 July 2024 9,201 2 View

How can we calculate the water balance in a hyper-arid climate zone? What should be the most appropriate formula for a desertic area?

Hi friends, How can we calculate the water balance in hyper-arid climate zone? If the water balance is still considered deficit in hyper-arid climate areas notably in the saharan area , how can...

26 June 2024 3,495 10 View

How to evaporate DMF from solution? Knowing that rotavap doesn’t work. Could anyone help?

23 June 2024 1,858 0 View

Why is there no condensation in my Star-CCM+ fluid film multiphase case?

Hello, I am attempting to get condensation modelling working from a steam/CO2 multi-component gas mixture to a fluid film of water on a cold wall in Star-CCM+. The gas enter the domain above...

12 June 2024 6,095 0 View

Pressure Drop and heat transfer in stator slots indents ?

Study case : turbo-generator cooling I have a small rotor-stator gap with slots on the stator. The rotor is rotating at high RPM (around 10,000 RPM). The cooling fluid is also circulating...

10 June 2024 579 0 View

Isssues making a thin film of lipids for nanoliposomes?

Hello, Im trying to make a nanoliposome to encapsulate plasmid DNA. I am using the standard thin film method followed by resuspension in sodium acetate 25mM pH4 with my DNA (Im using the...

05 June 2024 3,646 3 View

Why does the aloe vera gel change color from white to pink when placed in the refrigerator?

While when placed in the freezer, it maintains the same original white color?

05 June 2024 5,231 5 View