What is the operating density in ansys fluent?

03 March 2018 0 659 Report

what is the operating density in ansys fluent if my fluid domain is submerged in water?

Badges
Science topic

More Abdullah Al Noman's questions See All

I ran a simulation of parallel flow shell and tube heat exchanger. but didnot find any temperature variation radially in tube and shell wall.is it ok?

hot fluid was passing through shell side and cold fluid passing through tube. convection heat transfer boundary condition assigned to the outer shell wall. but I did not find any temperature...

07 August 2018 5,765 8 View

How to measure the surface temperature of a body exposed to sun?

A body exposed to sun. It also transfer heat to surroundings by convective. Now how to calculate surface temperature of the body? Or suggested some article on this topic.

06 July 2018 8,030 3 View

What is the advantage of using Cut cell meshing in a heat transfer problem?

Im trying to find out enhancement of heat transfer in a pipe due to using twisted tape insert in ANSYS Fluent. but if i use cut cell mesh, the rate of heat transfer in not same as normal...

05 June 2018 8,037 3 View

How to simulate free/natural convection in fluent?

this is (in the picture) 1/4th of my problem. oil is passing through the elliptical pipe, temperature 350K. the oil is cooled by free convection heat transfer by air surrounding of the pipes....

03 April 2018 2,639 0 View

What is the reason behind back flow at the outlet of ansys fluent?

a simple laminar pipe flow (water) with velocity inlet and pressure outlet boundary condition. outlet P(gauge)=0. operating P=101325. operating density =1.223. back flow occurring at the outlet....

02 March 2018 2,271 1 View

Is it possible to increase convective heat transfer by applying more turbulence in a flow which is already a turbulent flow?

I am tring to simulate a turbulence flow convection heat transfer. without insert the flow is turbulent. when I inserting a twisted insert in the flow, the heat transfer rate is not changing....

02 March 2018 8,654 17 View

How to apply dirichlet boundary condition on a wall which is a function of wall coordinate in consol multiphysics or ansys fluent?

I want to apply a variable heat flux on a wall which is a function of wall Y coordinate. i use comsol multiphysics software to simulate heat transfer by fluid through a pipe and a variable heat...

01 February 2018 8,026 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View