hello everyone
i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it.
what's the problem?
any suggestion.
I don't use Fluent but if you export the results and pull the data into Tecplot, it will extract and draw isosurfaces.
Dudley J Benton
okay thank tou sir.
What's the issue? Attach a screenshot of the problem. If you have computed the results it should work fine
Shahbaz Ali
thank you for your interaction.
i did find the issue which is the need of the initialisation.
I'm fairly new to making homemade comp cells and have done so with some mild success. What is generally an acceptable way of resuspending comp cells during wash steps? I've been told to swirl the...
31 July 2024 8,309 0 View
This question aims to explore the intersection of artificial intelligence and autonomous vehicle technology. It seeks to identify the key challenges faced in implementing AI for recognition...
20 July 2024 3,469 2 View
This question seeks to explore the role of artificial intelligence in improving the prediction models for climate change impacts on agriculture. It aims to understand how AI technologies, such as...
20 July 2024 7,647 3 View
Les géopolymères offrent plusieurs propriétés intéressantes qui peuvent être exploitées dans diverses applications innovantes : 1. Construction durable : - Bétons à faible empreinte carbone -...
10 July 2024 7,457 1 View
Geopolymers have gained attention for their potential in immobilizing radioactive waste. Recent studies indicate that they offer a promising alternative to traditional cement binders. Geopolymers,...
06 July 2024 9,797 0 View
It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...
01 July 2024 617 3 View
Kindly provide their URLs. Thank you
30 June 2024 8,475 0 View
Q3- or - Q4 journal (SCOPUS Indexed Journals &WOS) fast publish (computer science) ?
30 May 2024 5,330 2 View
I am looking for a simple method to synthesize magnetic biochar from plant parts. Is there any?
30 May 2024 9,400 2 View
quantification of total protein in tissue homogenate depends on the measured parameter?? is it necessary for all parameters? or just a different way for calculation (ng/mg protein instead of ng/g...
26 May 2024 1,493 1 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
EMMS - Energy Minimization Multi-Scale
18 June 2024 5,857 2 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?
07 June 2024 9,030 3 View
Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...
05 June 2024 4,153 0 View
Hello all, I am doing some heavy simulations in Fluent using clusters. The models are not readable by laptop or desktop because they are very heavy. So, i have to take the contours in cluster...
25 May 2024 6,099 3 View