Contact experts in FLUENT to get answers
1,517 views 3,198 posts
Questions related to FLUENT
Hello.. I have to add this correction for near wall treatment in Ansys Fluent. I am not finding any example. Can anyone help? Thanks in advance.
03 September 2022 6,110 0 View
Kindly reply
27 August 2022 301 2 View
Hello, I am trying to run a simulation with real gas model from NIST using ch4a as working fluid. When I try to initialisate or run the simulation its not converging in Fluent, in my simulation,...
10 August 2022 4,529 4 View
internal flow over cylindrical, rectangular and ellipse shapes. outside is rectangular shape.
01 August 2022 9,605 14 View
I want to create a micro turbojet engine but i don't know from where I should to begin, so I don't know how calculate the engine shaft mil - the distance between kompressor and turbine, combustion...
17 July 2022 9,954 2 View
What is the mechanism of fuel and oxidizer mixing used in ISRO's designed VIKASH Rocket engine?
05 July 2022 9,690 2 View
could anyone clarify that whether can we use Sparse matrix multiplication in parallel distributed system or is it restricted only to Distributed system? If so pls help me with algorithm
03 July 2022 8,581 2 View
Please? How to look for the standard state entropy from Fluent software in material?
30 June 2022 8,996 0 View
How can I calculate entropy, and exergy efficiency in ANSYS FLUENT?
20 June 2022 8,675 3 View
I am currently attempting to do a KMC simulation (using LAMMPS) to calculate the diffusion coefficient of an Inconel-Ni alloy using LAMMPS. As a part of that, I would like to know how to...
02 June 2022 7,335 0 View
explain your idea
30 May 2022 8,165 4 View
Hello everyone, I am working on the aerodynamics of blades of a Horizontal axis wind turbine .I want to know how to pick the best airfoils along the blade studied . for example if I have a 100 kw...
19 May 2022 3,747 11 View
my turbine is a variable speed wind turbine.
19 May 2022 7,210 4 View
Weather Station network is installed in a city to understand to local climate conditions. The meteorological data like air temperature, relative humidity, dew point, precipitation, etc. is...
28 April 2022 6,507 11 View
I did a single fibre tensile test on some natural fibre samples, I was able to calculate the stress and strain using the data obtained from the test (i.e. Force and Elongation). However, I'm also...
22 April 2022 6,298 2 View
I have found a lot of related 2D bubble simulations, but I can't find the settings for 3D model bubble simulation. I want to ask how to set it up, and how to fully present the bubbles in CFD-POST?
17 April 2022 845 1 View
i have been working on ASTM standard model in ANSYS workbench. its been crashing due to error message says, "your product license has numerical problem size limits, you have exceeded these problem...
08 April 2022 1,751 4 View
First I simulated scramjet problem using k-e model in fluent. The results are validated using literature after that necessary modification was done in boundary conditions using same mesh. The...
04 April 2022 8,748 3 View
Hi all, I'm doing multiphase FSI coupling using OpenFOAM and an in-house solid solver, connected by a coupling library preCICE. I'm trying to study the interaction between a caisson breakwater and...
30 March 2022 8,001 8 View
I am doing a 2D pure shear isochoric strain analysis with 20% pure shear in ansys workbench using ansys static structural in ansys workbench. Previously in ansys mechanical apdl, there is a scope...
23 March 2022 4,259 2 View
Hi everyone, I am trying to simulate turbulent flow over a sphere with the following conditions: Freestream velocty= 100m/s ambient density and viscosity Sphere diameter = 0.82 m Reynold's number...
21 March 2022 6,640 3 View
I am a bit skeptical regarding which mutli phase solver I should go with, interIsoFoam or twoPhaseEulerFoam. My case involves water and oxygen entering into a two-phase separator with gas...
21 March 2022 4,723 0 View
Hi, I am interested to know that why one should use a reference point in applying say , a displacement of say 1 unit to a face of an assembly and not directly applying the displacement to...
18 March 2022 1,466 6 View
I'm looking for an example of using overset-mesh combined with morphing using star CCM+ ?
14 March 2022 8,463 2 View