How cohesion parameter COHE effects the frictional stress in ansys for coulomb frictional module?

More Ankush Pratap Singh's questions See All

How to update material properties during the analysis in ansys?

I need to update the material property during analysis as per the stress coming in the element.

01 February 2020 8,163 3 View

I need to simulate two way fluid solid interaction using ansys fluent and ansys transient structure. can anybody suggest me how to do it ?

i know how to formalize the analysis using system coupling but i need some detailed knowledge about setting conditions and parameters to conduct the analysis.

11 December 2019 868 5 View

How to implement S-FEM smoothed finite element method in ansys for using meshless meshing?

i want to use smoothed finite element method for mesh-less meshing. So, i wantt to know how to use it in ansys?

11 December 2019 9,355 2 View

How to transfer structrual result to fluent by FSI in ansys?

I am working on blood flow simulation through arteries and want to know the effect of artery wall(deformable) properties on fluid. I am not getting how can I see the effect of structure on fluid.

10 November 2018 4,213 3 View

IS pinball radius influence the contact pressure magnitude in Ansys?

increase or decrease in pinball radius can cause in change in magnitude of contact pressure.

10 November 2018 9,957 0 View

Why my contact status changes from contact to no contact?

my contact status changes from contact to no contact in second sub-step of my analysis. In first sub-step contact is made and contact pressure generated but in next sub-step contact changes its...

10 November 2018 8,772 1 View

How to get rid of contact chattering in ansys mapdl?

My simulation is not converging because of contact chattering value which i found is 1. I am using augmented Lagrangian method with FKN-1, PINB- 0.1, FKT-1, FTOLN- 1, RESULTING PENETRATION...

08 September 2018 9,600 1 View

Convex or concave surface which should be target, if both are in contact using ANSYS? R1 value is required or not?

Actually i am providing contact between concave surface and convex surface. As per manual, i uses concave surface as target surface and convex as contact. But an error with statement " Contact...

08 September 2018 4,782 0 View

How to successfully translate one body in between load steps to make assembly with other body in ansys ?

i want to make assembly of cylinder and open ring (as shown in attachment) to find out the pressure exerted at the cylinder surface when ring mounted over it. Diameter of ring is less than...

07 August 2018 9,872 0 View

How to model unloading in terms of displacement loading?

I need to expand one horse shoe shape geometry. I give displacement loading at its both end to expand the gap between two ends. I used loadstep file to perform this Loadstep 1 Time,1 i selected...

07 August 2018 8,016 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View