IS pinball radius influence the contact pressure magnitude in Ansys?

Ankush Pratap Singh @Ankush_Singh13

11 November 2018 0 10K Report

increase or decrease in pinball radius can cause in change in magnitude of contact pressure.

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Ankush Pratap Singh's questions See All

How to update material properties during the analysis in ansys?

I need to update the material property during analysis as per the stress coming in the element.

01 February 2020 8,163 3 View

I need to simulate two way fluid solid interaction using ansys fluent and ansys transient structure. can anybody suggest me how to do it ?

i know how to formalize the analysis using system coupling but i need some detailed knowledge about setting conditions and parameters to conduct the analysis.

11 December 2019 868 5 View

How to implement S-FEM smoothed finite element method in ansys for using meshless meshing?

i want to use smoothed finite element method for mesh-less meshing. So, i wantt to know how to use it in ansys?

11 December 2019 9,355 2 View

How to transfer structrual result to fluent by FSI in ansys?

I am working on blood flow simulation through arteries and want to know the effect of artery wall(deformable) properties on fluid. I am not getting how can I see the effect of structure on fluid.

10 November 2018 4,213 3 View

Why my contact status changes from contact to no contact?

my contact status changes from contact to no contact in second sub-step of my analysis. In first sub-step contact is made and contact pressure generated but in next sub-step contact changes its...

10 November 2018 8,772 1 View

How cohesion parameter COHE effects the frictional stress in ansys for coulomb frictional module?

The frictional stress for coulomb frictional model is defined as sum of cohesion parameter and mu*contact pressure.

09 October 2018 5,993 2 View

How to get rid of contact chattering in ansys mapdl?

My simulation is not converging because of contact chattering value which i found is 1. I am using augmented Lagrangian method with FKN-1, PINB- 0.1, FKT-1, FTOLN- 1, RESULTING PENETRATION...

08 September 2018 9,600 1 View

Convex or concave surface which should be target, if both are in contact using ANSYS? R1 value is required or not?

Actually i am providing contact between concave surface and convex surface. As per manual, i uses concave surface as target surface and convex as contact. But an error with statement " Contact...

08 September 2018 4,782 0 View

How to successfully translate one body in between load steps to make assembly with other body in ansys ?

i want to make assembly of cylinder and open ring (as shown in attachment) to find out the pressure exerted at the cylinder surface when ring mounted over it. Diameter of ring is less than...

07 August 2018 9,872 0 View

How to model unloading in terms of displacement loading?

I need to expand one horse shoe shape geometry. I give displacement loading at its both end to expand the gap between two ends. I used loadstep file to perform this Loadstep 1 Time,1 i selected...

07 August 2018 8,016 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

How Do Length of Pylon and Rotor Disk Radius Impact Angular Frequency and Torsional Stiffness in Whirl Flutter Analysis for a 2 DOF Propeller System?

Actually, I'm having trouble implementing the plot of the flutter region for the whirl prop system with 2 DOF (Influences of structural damping and propeller—pivot point distance on whirl flutter...

21 July 2024 5,047 2 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

How to get discharge capacity of a bole well?

No data regarding radius of influence is provided and no pumping test data available.

10 July 2024 7,168 0 View

How can I find the absolute maximum value of the Lamb-Oseen vortex with a no-slip condition?

R(t) = the propagation function of the vortex, where R=sqrt(4vt + R0^2) R0 = initial radius. w0 = initial angular velocity. Rf = the radius of the boundary confining the fluid. The Lamb-Oseen...

07 July 2024 3,680 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View