How to simulate the energy yield of an Organic PV module based on the Temperature effects and the albedo effects?

26 December 2020 4,280 5 View

One diode equivalent circuit for OPV always has a coupled variable in the end. How to find the Power with diff. temp and diff. Irradiation values?

I am writing my master thesis to simulate Energy Hatvest of OPVs in A year. Any advice on the same would be helpful.

03 December 2020 8,915 1 View

How to validate the air pollution (remote sensing data ) with ground measurement data, is there any application available?

i am currently doing project in "IMPACT OF URBANIZATION ON AIR QUALITY", so i am using remote sense air pollution data from MODIS, OMI and TROPOMI (parameters like so2,no2 and aerosol) to mapping...

05 November 2020 1,579 4 View

Where can the antibacterial, antimicrobial, anticancer and anti-plasmodic activities of organic molecules be performed?

I have novel organic molecules for which the biological activities have to be performed. So can i know the places or researchers who can test the activities.

18 March 2019 6,832 4 View

How bubble formation and crystals formation can occur simultaneously when we heat a gas saturated semi-crystalline polymer?

How bubbles can sustain heat? when try thermal induced crystallisation?

29 May 2018 4,056 3 View

How to design driving cycle for electric vehicle and How to compare it to standard Indian driving cycle? And what is the concept of driving cycle?

21 August 2017 5,908 4 View

Need data set for Machine learning to study log files to predict potential system failures -

Need data set for Machine learning to study log files to predict potential system failures -

04 June 2017 9,291 3 View

Which institution has the largest holding of living tropical species in Asia?

Can anybody suggest the name of an institution having a maximum number of living plant species in Asia?

14 May 2017 2,822 3 View

What are these cells in L929 culture?

It is my first time working with L929. I cultured the L929 from stock purchased from ATCC (CCL-1). I observed these large cells amongst the L929 from P0 up to P2. Not sure what it is but when 80%...

06 April 2017 8,820 1 View

How can I create a damper/spring-foundation under a steel beam in dynamic explicit in Abaqus ?

Hi, I am new to abaqus. I am modelling a steel cantilever beam under impact loading in abaqus. I used solid-homogeneous as my section. I created a step "Dynamic-Explicit"(time period=0.01),...

25 February 2017 1,542 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View