What is the degassing condition to do BET surface analysis of Zn-BDC and Co-BDC MOFs ?

More Santhosh Wodeyar's questions See All

How can I get a project topic and a research paper related to that topic?

I am a final year Msc. Applied Statistics student. For my project I need a topic and a research paper related to the topic. Please guide me.

26 October 2023 8,853 1 View

How to interpret EIS data of my perovskite solar cell?

The interpretation of the results of EIS is divided into two parts. on one hand, some researchers insist that larger semicircle is better because it leads to larger recombination resistance...

22 August 2023 7,742 2 View

Why does nanodrop show negative values for dye labelled ssDNA?

I prepared a ssDNA sample in nuclease free water which is dye labelled and took its concentration using a nanodrop instrument. But the instrument is giving negative values for the dye and positive...

25 April 2023 7,652 2 View

Can someone please explain me the isolation procedure for bacterial protein from the supernatant (CFS) ?

I am actually trying to isolate bacterial lipopeptides from the supernatant. i tried isolating with 1) ethyl acetate and flash 2) acid precipitation and concentration explained in most of the...

14 April 2023 234 0 View

What may be the reason for foggy/whitish perovskite film after spincoating?

After spin coating, there will be a whitish or foggy perovskite film observed. in both one-step and two-step cases, it is happening. I cant get mirror like films. perovskite : triple cation...

20 March 2023 411 1 View

I would like to calculate the gas yield of a gas generating propellant. How the gas yield can be experimentally determined on a small scale level?

Method of determination of gas yield of a composite propellant.

18 December 2022 3,382 0 View

What is the recipe to prepare MOPS-KOH buffer?

I need a buffer for RNA studies which has both sodium and potassium ions. From some research papers I found that some labs have used MOPS-KOH buffer, but it is not available to buy when I searched...

03 November 2022 1,443 3 View

Which is the best journal for Bioinformatics research publication?

As usual Good quality Peer reviewed Reasonable APC (need not sell my kidneys for a paper) or Free Rapid review Good acceptance (not reject with universal stupid Submission declined...

14 October 2022 7,291 6 View

How the pH affect on the potential during electrochemical studies?

while study of effect of pH during development of nanosensor through cyclic voltametry technique i experienced shifting of analyte peak in x-axis at different pH. what is the role of pH?

13 September 2022 8,409 0 View

Is this necessary to study the magnetic property of iron while the studying the effect of iron in heme group?

to study the structure and function of hemoglobin in bioinorganic chemistry is it necessary to know the magnetic property of the Fe2+ and Fe3+

09 June 2022 2,168 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

What is the difference between coordination polymer, MOFs, MCOFs?

Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.

21 July 2024 3,045 3 View

What is the degassing temperature and time for biochar for BET surface area analysis if TGA is not possible?

Since BET and TGA both are very costly instruments and many places the facilities are not available (for large number of samples) hence a threshold degassing temperature and time is preferable

16 July 2024 8,112 2 View

How to determine the acceptable amount of DMF when synthesizing MOFs?

I have synthesized MOFs already. However, I need to scale it up to produce 100g of MOFs. During my calculation, I need 15L of DMF just for this synthesis! So I thought, maybe DMF is just used as a...

01 July 2024 1,905 1 View

Why does a nitrogen adsorption-desorption isotherm form two loops?

BET analysis

27 June 2024 6,964 1 View

What should be the degassing temperature and time for BET surface area analysis of ZIF-67?

Kindly guide me to choose an appropriate degassing condition.

11 June 2024 1,574 1 View

Knowing the CIF file No?

I am working on metal-organic framework for supercapacitor application. so, i want know about the Bi-trimesic acid CIF file number and Cerium also

09 June 2024 3,877 0 View

Can anyone explain how to determine degassing temperature and time for biosynthesized nanomaterial for BET analysis?

I have also attached TGA and DSC analysis of biosynthesised nanomaterial.

30 May 2024 1,565 1 View

Is it normal to wash metal-organic frameworks with DI water for a week?

I have synthesized MOFs and been washing for about 2 weeks now until I reach the goal of UV absorbance of near 0.

27 May 2024 2,295 0 View

Can someone tell me ? Is there any effect on BET surface area of activated carbon on degassing temperature and time?

What are the ideal degassing time and temperature of activated carbon for BET surface area analysis?

25 May 2024 2,157 3 View

Julián E. Sánchez-Velandia

Hello, for MOFs I usually try to use 120 celsius (2 celsius per min) for 4 h at vacuum conditions. BR, Julián.

Garima Chaturvedi

Santhosh Wodeyar Try to do degassing at 80 degrees for around 10-12 hours in vacuum condition.

Nandisha P S

Firstly, for the analysis of BET, first you have to do TGA analysis. from that you get to know, decomposition temperature of your material. usually, 80- 150 degree Celsius range is set as a degassing temperature for your like samples.