Contact experts in Annealing to get answers
10,665 views 670 posts
Questions related to Annealing
After undergoing a solution heat treatment (air quenched) and full annealing heat treatment on my stainless steel samples it was observed the hardness of full annealed samples is more than air...
02 February 2019 6,933 9 View
Hi all! Does anyone tried to perform agarose gel electrophoresis of crRNA:tracrRNA duplex after annealing? How many bands do I expect to observe if the annealing is successful and how many if the...
02 February 2019 4,291 2 View
I am looking for simple drop casting of ZnO nano rods on FTO glass. But most of the time film gets peeled off after annealing while being used for further processes.
10 January 2019 8,002 3 View
Silver being FCC metals forms annealing twins in wrought materials. These twins are hinder the grain size analysis. What options are possible to obtain grain size of pure silver without etching twins.
01 January 2019 10,035 3 View
Hello everyone! I'm studying GaAs grown on Si at low deposition temperature with post-growth annealing which have mosaic structure. Did you find any articles about formation mechanism of this...
01 January 2019 9,130 2 View
I'm wondering if anyone is aware of published literature that describes the PCR cloning technique I've just used. I'm aware of this paper, which is very similar but introduces a DNA fragment as an...
01 January 2019 3,289 3 View
Post annealing is an important parameter in thin film fabrication, which can help to enhance the physical, optical and electrical properties of the thin film by changing the microstructure and...
12 December 2018 3,804 4 View
How can the wire producer or the customer control the effectivnes of annealing process to get enough soft wire? Are there some limit values of mechanical properties to test Al-conductor class2...
12 December 2018 5,143 5 View
Do you know what is the influence of the furnace pressure in the coils wraps when annealing? Is there any flow of hydrogen gas when purging through the coil wraps? I'm looking for it but i just...
12 December 2018 7,761 1 View
As you know we have 2 kinds of dislocations in the dislocation accumulation procedure. Statistically Stored Dislocations (SSDs) and Geometrically Necessary Dislocations (GNDs) which either of them...
12 December 2018 2,766 4 View
12 December 2018 5,172 5 View
My polymer is PLA and I follow the following steps (DSC 25): first heating " rate 10 C/min- fixed at 200 C for 5 min"--> remove the thermal history cooling " rate 5 C/min - fixed for 2 min...
19 November 2018 3,944 3 View
Do non-metallic inclusions in stainless steels coarsen during a solution annealing treatment and how fast?
11 November 2018 534 0 View
11 November 2018 7,626 4 View
Hello, I have annealed a HDPE powder near its melting temperature for different durations. What I have observed in their DSC analysis is the appearance of a secondary endotherm with a lower...
11 November 2018 8,341 1 View
How can one calculate the oxygen vacancy from XPS data? And also if annealing is used to introduce defects, what method can be the best to estimate the presence of defects? Thank you
11 November 2018 1,289 5 View
Annealing means selenization (Se Powder/ Se pellets) on RbIn spray deposition surface.
11 November 2018 6,624 1 View
02 November 2018 4,996 1 View
I deposited both precursor solutions at 2000rpm for 30s and after annealing i got a brown colour.
27 October 2018 9,121 3 View
As in GaN after annealing the quality of gold markers degrades, how can I keep my markers quality same as before or improve it after annealing process?
12 October 2018 3,571 1 View
I fabricated my perovskite using PEDOT:PSS/MAPbI3/PCBM/Al. After depositing the back contact (Al), I annealed the cell again at 100 degrees for another 10 minutes. I obtained no PCE. I would like...
10 October 2018 5,950 3 View
I have soda lime glass slides (75x50x1mm) with a Ti-Pt thin film sputtered onto it (Ti-2nm, Pt-200nm). I want to anneal it for long term stability and reduction in resistance of the Pt layer. The...
10 October 2018 2,946 3 View
10 October 2018 9,316 3 View
10 October 2018 2,464 1 View