Can anyone tell me the appropriate annealing condition (temperature) for the stable phase formation of RbInSe2 ?

Salahuddin MINA Sobuj @Salahuddin-Sobuj

02 November 2018 1 5K Report

Annealing means selenization (Se Powder/ Se pellets) on RbIn spray deposition surface.

Raghav Raaja

Try 0.7 percentage of the melting point of the base substrate.

Badges
Science topic

More Salahuddin MINA Sobuj's questions See All

Being healthcare Provider , im student of EMBA in healthcare management at lumhs jamshoro, need help in choosing topic for research article?

Being healthcare Provider, i need help for research article related to health problems in content to management ?

03 November 2023 7,117 6 View

What is the effect of curing temperature on mass loss of concrete at elevated temperatures?

can anyone has gone through some research paper or personal experience regarding study of elevated temperature performance of concrete, prepared under different curing regimes... I was looking for...

12 February 2020 8,504 5 View

What are the different methods of estimation and interpretation of Somatic Cell Count in Mastitis?

I want to estimate the somatic cell count from Mastitic milk in caprine and bovines. For this I want to know the procedure, different methods and interpretation of SCC. If any researcher have...

02 November 2017 628 7 View

As the virus causing Rabies can't sustain on other than body of host, why is it still not eradicated?

I feel that it is possible to eradicate Rabies all over the world. As the virus of Rabies, Lyssa virus of Rhabdoviridea, can't live outside the host. But the fact is that it is still causes huge...

29 October 2017 2,372 13 View

What kind of error/erasure detection and correction codes are used in modern hard disk drives?

This question is still unanswered for me. Like CDs use Reed-Solomon codes for this purpose. It would be great that some one could refer me to some technical paper on this particular topic. Thanks

24 October 2016 9,055 5 View

How can I prepare Brewers Yeast suspension 20% in NS and inject subcutaneously in rats? What is the size of needle use?

I cannot inject using 22G needle without filtering the suspension. After filtering and injecting 15ml/kg to the rats, after 18hours, the rats are not feverish. Can anyone give me answers??

19 September 2015 4,107 1 View

How are the RF power, self bias voltage and electrode size related in Reactive Ion Etching system?

Hi, I am trying to adopt an anisotropic silicon etch recipe to Oxford NGP80 RIE machine. The Original recipe has been optimised for a different machine (NEXTRAL 330 RIE parallel plate plasma...

07 September 2015 2,425 4 View

Can I expect same/similar results for 2D and 3D FDTD simulation as the ones from the simulation of very High-Q photonic crystal cavities?

Hi, I need to realise/fabricate very high-Q photonic crystal cavities in silicon for my PhD project. The cavities should be optimised for certain wavelength range (around 1078 nm). I am trying...

05 July 2015 2,017 4 View

Can somebody send me the questionnaire of all items in the LTSI version 3?

I want to construct a questionnaire for my research keeping in view the questions suggested in LTSI version 3.

04 January 2015 4,324 1 View

Which Wire is better to connect the electrode?

I am fabricating the glucose biosensor based on ZnO nanorods over the gold thin film. I have to carry out the CV measurement. Can you please help me to know which wire (either Pt or Ti) should i...

20 November 2014 5,850 20 View

Why my gel electrophoresis has smearing?

Greetings. I’m currently running a nested pcr for giardia. My mastermix comprised of 3mM Mgcl2, 5unit of taq polymerase, 0.2uM of forward and reverse primers each respectively and 0.2mM of dNtp...

22 July 2024 9,761 5 View

What is the reason for the non-monotonic variation of roughness for sputtered Cu films annealed at 100, 200 and 300 degree Celsius?

I have prepared Copper thin films by magnetron sputtering and the samples have been annealed at 100, 200 and 300 degree celsius. The variation of the rms roughness and all other AFM height related...

11 June 2024 9,774 1 View

Why am I getting a visible band in my negative control(which contains only nuclease-free water and no DNA template) in PCR?

I am doing my undergrad thesis that requires me to do PCR-RFLP analysis on DNA that I extracted from some blood samples. Initially, I was using the Qiagen mastermix for the optimization of my...

14 May 2024 4,370 4 View

Any thoughts on troubleshooting my CC9 KO experiment?

Hi, I'm currently trying to generate a one-vector plasmid system for a knockout using CRISPR/Cas9. I'm using lentiCRISPRv2 (ampicillin-resistant) and following the GeCKO Target Guide Sequence...

29 April 2024 3,660 0 View

Regarding primers annealing temperature ?

I recently designed the qrtpcr primers from the 3'utr of the plant's genomic DNA keeping in mind that the annealing temperature should be 60 degree. Once I received the primers first to optimise...

25 April 2024 5,935 3 View

Why is there no Ligase in Ligation Independent Cloning?

Ligation Independent Cloning literally says no need Ligation, but it still needs ligase to anneal the fragment to vector. And the Protocol used T4 DNA Ligase for anneal process. What does this...

18 April 2024 1,494 3 View

Why are there smaller than 100bp bands?

Hi, I have been trying to decide on the best annealing temperature for the F/R primers using a sample. From left is the ladder, 61c, 63c, 65c, no template and the ladder. The expected product size...

11 April 2024 7,592 9 View

Why could amplicon sizes appear bigger than they should on agaose gel electrophoresis?

I did PCR of 6 amplicons and when I did agarose gel electrophoresis, they all appear consistently bigger than they should be (e.g. the amplicon should be 4000 bp, but is around band of 5000 bp...

09 April 2024 4,487 5 View

Related how to Anneling in Silvaco TCAD ?

When I simulate the NMOS model in ATHENA, when I want to anneal in nitrogen atmosphere after n+ ion implantation, the annealing operation is not possible when the annealing temperature is lower...

08 April 2024 2,798 0 View

Help for Mitochondrial 16S rRNA PCR?

Hi All, I am trying to amplify mitochondrial 16S gene for marine snails (Calliostomatidae) and other vetigastropods, but I only get primer dimers or nothing on the gel. These primers have worked...

03 April 2024 8,736 4 View