I got PVA nanofiber with dimeter in range 60-80 nm ..
But i want to increase diameter to be in range 95-110 nm.
First of all, an increase of solution concentration or molecular weight of polymer dissolved will result in fibers diameter increase. Also, a decrease of the voltage applied will lead to the same result.
Best regards.
Dear Somaya A.Amer
1. Increase Solution Concentration.
2. Increase the Flowrate.
3. Try finding the minimum Voltage required to get bead free fibre.
good luck.
HI,
I suggest that you make changes slowly, if you follow all the recomendations probably fibers will increase their diameter more than you want.
Before increase solution concentration, try with minimum voltage, short collector-needle distance and a little more flow.
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
Hi guys, I want to investigate a CFD study of Ampair300, and I need the geometric data of this turbine's blade : chord and twist angle distribution. Thank you.
22 May 2024 5,519 0 View
There are LMI, UKF and Adaptive Observers for various neuron models. Which one really works?
10 October 2023 9,508 0 View
I need to submit my manuscript to a journal with fast publication-it can be paid-. The paper is about fluid Mechanics related to wind turbine aerodynamic prediction using numerical method.
14 August 2023 1,828 1 View
I'm working on quantifying cell dynamics on a three-dimensional matrix and rely heavily on three-dimensional microscopic images. However, I was never able to capture high-quality images of my...
03 July 2022 7,135 0 View
Hi guys, I investigate an aerodynamic study of an HAWT using Ansys Fluent. After solution convergence I need to calculate the loads on the blade turbine using CFD-post. How can I do this? Thank you.
09 February 2022 2,102 3 View
I want to know the complexity analysis (Time and Space ) of the algorithm of multi-task learning deep neural network-based compared to the conventional algorithms.
08 January 2022 569 3 View
Hi, I am simulating a horizontal axis wind turbine using Ansys Fluent. I want to validate the model by calculating the turbine power at different wind speed. Using Fluent, I calculate the torque...
08 January 2022 2,664 5 View
Hi everyone, I simulate a three bladed wind turbine using Ansys Fluent. The variation of wind turbine torque with tip speed ratio must have a peak. But in my case, as tip speed ratio increases ,...
07 December 2021 7,412 4 View
Hello Everyone, I am simulating a small wind turbine using Ansys Fluent 19.0. Because of problem periodicity only one third of the fluid domain is simulated. The generated power is calculated...
06 December 2021 8,601 3 View
Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...
18 July 2024 9,725 1 View
I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...
08 July 2024 3,714 1 View
I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...
17 June 2024 9,763 0 View
Recently, I am preparing novel electrospun nanofibers for forward osmosis membrane preparation, I am facing following problems: 1. While testing water flux, there is little leakage, although the...
28 May 2024 8,510 2 View
Recently, i use Cd as a doping for ZnO Nanofiber. From some journals, Cd should increase the absorbance of ZnO. But in my case; it was not. Cd-ZnO Nanofiber has lower absorbance than the pure one....
12 May 2024 1,013 4 View
The FTO is deposited on glass substrate
01 May 2024 9,262 1 View
I have used DMSO to treat films with DMSO vapour. Can I use that same DMSO solution multiple times again?
04 April 2024 5,882 2 View
I added 4mass% also get the results of beads clumped together. Is it because the ethanol does not mix well with PET/HFIP?
29 March 2024 2,164 0 View
I have synthesized a nanoparticle which has piezo electric property and dispersed in the polymer solution to prepare nanofibres through the process of electrospinning. Is there any standard method...
18 March 2024 6,780 1 View
I am modelling a Low Velocity Impact (LVI) test. I have set the impactor as 'discrete rigid' while checking the box for 'CFN' with a set of the surface of impactor. In the 'interaction' module I...
14 March 2024 6,163 0 View