How can I immobilize Glutathione on to PCL electrospun nanofiber?

Abdurohman Mengesh Yessuf @Abdurohman-Yessuf

19 July 2024 1 10K Report

Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or coelectrospinning for biomedical application?

Thank you

Abdelkader BOUAZIZ

Dear Abdurohman Mengesh Yessuf, please read the following free access paper. My Regards

https://doi.org/10.3390/pr10030512

Badges
Science method

More Abdurohman Mengesh Yessuf's questions See All

What is the recommended solvent and solvent ration for PCL electrospinning to get bead free fiber?

I tried DMF( 100%), and DCM:DMF, in different rations, for DCM:DMF(4:1) I found elastin fiber mate with so many beads.

24 January 2024 9,245 3 View

How to quantify fibrin formation for absorbent hemostatic biomaterial ?

I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...

08 July 2024 3,714 1 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View

Is Polyethylene terephtahalate (PET) back support is suitable for electrospun nanofibers for forward osmosis membrane preparetion?

Recently, I am preparing novel electrospun nanofibers for forward osmosis membrane preparation, I am facing following problems: 1. While testing water flux, there is little leakage, although the...

28 May 2024 8,510 2 View

How to calculate the TPU ratio using [NCO/OH] formula ?

Greeting, I am using PCL and IPPDI to produce the Thermoplastic Polyurethane with different ratio. I would like to calculate the amount of PCL and PPDI that need to produce 0.2 and 0.4 ratio of...

23 May 2024 9,448 0 View

Why does my Cd-ZnO Nanofiber has lower absorbance than pure ZnO Nanofiber?

Recently, i use Cd as a doping for ZnO Nanofiber. From some journals, Cd should increase the absorbance of ZnO. But in my case; it was not. Cd-ZnO Nanofiber has lower absorbance than the pure one....

12 May 2024 1,013 4 View

I am trying to deposit nanofibers on FTO glass substrate, Is it possible to place FTO on rotating drum which have negative potential ?

The FTO is deposited on glass substrate

01 May 2024 9,262 1 View

Can I reuse DMSO heated at 45 C ?

I have used DMSO to treat films with DMSO vapour. Can I use that same DMSO solution multiple times again?

04 April 2024 5,882 2 View

I added 3mass% ethanol to PET/HFIP solution and carried out electrospinning, but the nanofiber I got have beads clumped together. Is this normal? Why?

I added 4mass% also get the results of beads clumped together. Is it because the ethanol does not mix well with PET/HFIP?

29 March 2024 2,164 0 View

How to measure Piezo electricity of a material?

I have synthesized a nanoparticle which has piezo electric property and dispersed in the polymer solution to prepare nanofibres through the process of electrospinning. Is there any standard method...

18 March 2024 6,780 1 View

Is stannous octoate necessary when making polyurethane?

When making medical TPU using PCL, some papers use stannous octoate, while others do not. Is stannous octoate really necessary?

18 March 2024 8,587 3 View