Does anyone have the geometric data (chord, twist and pitch ) of Ampair300 wind turbine ?

23 May 2024 0 6K Report

Hi guys, I want to investigate a CFD study of Ampair300, and I need the geometric data of this turbine's blade : chord and twist angle distribution.

Thank you.

Badges
Science topic

More Somaya Younoussi's questions See All

Does anyone know some Q1, or Q2 journals with fast publication in mechanical engineering, or wind energy modelling?

I need to submit my manuscript to a journal with fast publication-it can be paid-. The paper is about fluid Mechanics related to wind turbine aerodynamic prediction using numerical method.

14 August 2023 1,828 1 View

How can high-resolution images of cells on a 3D matrix be obtained?

I'm working on quantifying cell dynamics on a three-dimensional matrix and rely heavily on three-dimensional microscopic images. However, I was never able to capture high-quality images of my...

03 July 2022 7,135 0 View

How to calculate normal force along a wind turbine blade using CFD-post?

Hi guys, I investigate an aerodynamic study of an HAWT using Ansys Fluent. After solution convergence I need to calculate the loads on the blade turbine using CFD-post. How can I do this? Thank you.

09 February 2022 2,102 3 View

What is the equation used to calculate the wind turbine power ?

Hi, I am simulating a horizontal axis wind turbine using Ansys Fluent. I want to validate the model by calculating the turbine power at different wind speed. Using Fluent, I calculate the torque...

08 January 2022 2,664 5 View

Why the wind turbine torque increases as the tip speed ratio increases ?

Hi everyone, I simulate a three bladed wind turbine using Ansys Fluent. The variation of wind turbine torque with tip speed ratio must have a peak. But in my case, as tip speed ratio increases ,...

07 December 2021 7,412 4 View

How to calculate the generated power by an HAWT using Ansys Fluent?

Hello Everyone, I am simulating a small wind turbine using Ansys Fluent 19.0. Because of problem periodicity only one third of the fluid domain is simulated. The generated power is calculated...

06 December 2021 8,601 3 View

Can I consider the 1st scheme order solution as final solution of the simulation?

Hi guys, I am simulating an horizontal axis wind turbine using Ansys Fluent (steady state simulation). To get more accurate results I use second order upwind momentum discretization scheme, but...

24 November 2021 2,946 4 View

How to get a correct power coefficient of an HAWT operating at high rotation speed and low wind velocity?

Hi guys, I want to test a wind turbine performance with different rotation speeds and a fixed wind velocity. But when I used a TSR of 6,7,8,9 I found high torque coefficient so multiplied by high...

31 October 2021 857 1 View

How can stability of an aerodynamic body be applied on wind turbine field?

Hi, I am working on wind turbine aerodynamic and I want to know if the stability of an aerodynamic body like an aircraft can be applied in the wind turbine field. If you have any ideas or...

13 September 2021 5,585 4 View

What is your opinion about this mesh convergence study ?

Hi, I am working on small scale wind turbine. I use Ansys Fluent to investigate the rotor performances. Prior to the study, a mesh sensitivity test was conducted, the results of this study are...

05 August 2021 5,169 5 View

What is the difference between mathematical R^4 space and physical 4D unit space?

We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...

10 August 2024 6,678 14 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

Is there a database with onshore wind production for the wind farms in Portugal?

I am looking to predict some production for future onshore wind energy production in Portugal, is there any database with info of performances of the existing wind farms in the country? something...

28 July 2024 1,750 1 View

How to prepare a molecule for molecular dynamics calculations?

If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...

28 July 2024 673 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View