Need to rotate 10000 nodes to 5 degree, 10 degree upto 50 degrees.
I have to mark very very small (0.001 mm) permanent dot on steel specimen as a reference point.
04 May 2018 6,702 7 View
Need to bond Stainless steel orthodontic bracket on steel bar and twist the archwire for 50 degree.It should not get debond during archwire twist.
10 November 2017 1,168 1 View
Planned to attach a C clamp like stiff wire on 0.482 mm x 0.64 mm rectangular dental archwire. Is there any possibility? Constraint is that C clamp must with stand applied force (Rotation)...
05 June 2017 5,907 1 View
When we twist a bar inside a slot bar had contact on slot walls. Problem is bar is penetrating inside the wall. How to avoid. Contacts were made in Hypermesh, analysis done in ansys apdl.
08 September 2016 9,638 3 View
Need to find at what load plastic deformation takes place.
08 September 2015 7,488 0 View
I did multiple load steps with ansys transient, after some time when i applied zero force, my model gives some deflection, but within elastic limit, i think that deflection (DMX) should be zero,...
08 September 2015 9,192 7 View
I wish to do loading and unloading through ansys. i able to do transient time load step but i dont know how to do reverse loading?
05 June 2015 4,854 4 View
I have ansys results of my model. I wish to know whether plastic deformation happens in the model due to force.
05 June 2015 9,400 5 View
I have a solid model imported from hypemesh. The orientation of global coordinate system is inclined (x,y,z). when I apply any force/moment it goes along the direction of coordinates not the...
06 July 2014 7,857 5 View
Time varying load step.
05 June 2014 4,337 9 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
In cases where the rotational of the magnetic field H is zero, we can define this field as the gradient of a scalar function defined as the magnetic scalar potential (similar to the electric...
21 July 2024 9,633 4 View
Let's say I rotate a hexagonal crystal using Euler angles (φ1, φ2, φ3); and rotate another similar crystal using Euler angles (ψ1, ψ2, ψ3). What would be the angular difference between the final...
17 July 2024 5,582 1 View
A universe model compatible with VSLT The research of Halton Arp and Eric Lerner supports a stationary universe, and the intrinsic nature of redshift, i.e. not linked to its presumed expansion...
14 July 2024 4,092 5 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...
09 July 2024 1,969 0 View