I have a solid model imported from hypemesh. The orientation of global coordinate system is inclined (x,y,z). when I apply any force/moment it goes along the direction of coordinates not the direction which I want it to.
You can use local coordinate system instead
Thank you sir. but how to rotate the local coordinate system to the direction which i want?
Dear Magesh,
In ANSYS menu goto Workplane>>Local CS>> Create LCS>> At specifiied location.
You can find it, see the attached file
Thank you sir.
but sir, now how to translate that tool with the rotating it along the a fixed node on the top of the tool
like in the friction stir welding the tool rotates along the pilot node and translate along the weld line
I have to mark very very small (0.001 mm) permanent dot on steel specimen as a reference point.
04 May 2018 6,702 7 View
Need to bond Stainless steel orthodontic bracket on steel bar and twist the archwire for 50 degree.It should not get debond during archwire twist.
10 November 2017 1,168 1 View
Need to rotate 10000 nodes to 5 degree, 10 degree upto 50 degrees.
09 October 2017 7,698 0 View
Planned to attach a C clamp like stiff wire on 0.482 mm x 0.64 mm rectangular dental archwire. Is there any possibility? Constraint is that C clamp must with stand applied force (Rotation)...
05 June 2017 5,907 1 View
When we twist a bar inside a slot bar had contact on slot walls. Problem is bar is penetrating inside the wall. How to avoid. Contacts were made in Hypermesh, analysis done in ansys apdl.
08 September 2016 9,638 3 View
Need to find at what load plastic deformation takes place.
08 September 2015 7,488 0 View
I did multiple load steps with ansys transient, after some time when i applied zero force, my model gives some deflection, but within elastic limit, i think that deflection (DMX) should be zero,...
08 September 2015 9,192 7 View
I wish to do loading and unloading through ansys. i able to do transient time load step but i dont know how to do reverse loading?
05 June 2015 4,854 4 View
I have ansys results of my model. I wish to know whether plastic deformation happens in the model due to force.
05 June 2015 9,400 5 View
Time varying load step.
05 June 2014 4,337 9 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View