How can i do welding/soldering in a 0.482x0.64 mm rectangular wire like a c clamp on the surface of the wire?

06 June 2017 1 6K Report

Planned to attach a C clamp like stiff wire on 0.482 mm x 0.64 mm rectangular dental archwire. Is there any possibility? Constraint is that C clamp must with stand applied force (Rotation) approximately 5 Kg.

Franco Concli

please post an image of what you want to do.

Badges
Science topic

Similar topics
Physical Sciences
Mechanics

More Varadaraju Magesh's questions See All

How to mark tiny (0.001 mm dot on stainless steel) dot on steel?

I have to mark very very small (0.001 mm) permanent dot on steel specimen as a reference point.

04 May 2018 6,702 7 View

Which bonding agent is good for bonding orthodontic bracket on steel bar?

Need to bond Stainless steel orthodontic bracket on steel bar and twist the archwire for 50 degree.It should not get debond during archwire twist.

10 November 2017 1,168 1 View

How to rotate more number of nodes in degress in ansys APDL ?

Need to rotate 10000 nodes to 5 degree, 10 degree upto 50 degrees.

09 October 2017 7,698 0 View

How can avoid penetration of contact surfaces in ansys apdl, Contacts were created in Hypermesh.

When we twist a bar inside a slot bar had contact on slot walls. Problem is bar is penetrating inside the wall. How to avoid. Contacts were made in Hypermesh, analysis done in ansys apdl.

08 September 2016 9,638 3 View

Is it correct after input stress,strain by MISO table then E value and force then finding what force yield and ultimate reaches through ansys results?

Need to find at what load plastic deformation takes place.

08 September 2015 7,488 0 View

Why am I getting deflection after applied zero force in ansys transient analysis during elastic stage instead of zero deflection?

I did multiple load steps with ansys transient, after some time when i applied zero force, my model gives some deflection, but within elastic limit, i think that deflection (DMX) should be zero,...

08 September 2015 9,192 7 View

Can you suggest me, how to do unloading or reverse loading analysis by ansys APDL?

I wish to do loading and unloading through ansys. i able to do transient time load step but i dont know how to do reverse loading?

05 June 2015 4,854 4 View

Can you suggest how to find a model is subjected to plastic deformation based on ansys results?

I have ansys results of my model. I wish to know whether plastic deformation happens in the model due to force.

05 June 2015 9,400 5 View

Is there any possibility to alter the global coordinate system orientation in ANSYS classic?

I have a solid model imported from hypemesh. The orientation of global coordinate system is inclined (x,y,z). when I apply any force/moment it goes along the direction of coordinates not the...

06 July 2014 7,857 5 View

How to create multiple load step in ansys for a solid model?

Time varying load step.

05 June 2014 4,337 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

How to Input and Analyze Results for an Asymmetrical Factorial Design in STATISTICA 13.3?

In STATISTICA 13.3, I used the Experimental Design Builder under the Design of Experiments tab to generate a design matrix for an asymmetrical factorial design (1443) with 12 experiments. However,...

29 July 2024 4,155 2 View