Need to find at what load plastic deformation takes place.
I have to mark very very small (0.001 mm) permanent dot on steel specimen as a reference point.
04 May 2018 6,702 7 View
Need to bond Stainless steel orthodontic bracket on steel bar and twist the archwire for 50 degree.It should not get debond during archwire twist.
10 November 2017 1,168 1 View
Need to rotate 10000 nodes to 5 degree, 10 degree upto 50 degrees.
09 October 2017 7,698 0 View
Planned to attach a C clamp like stiff wire on 0.482 mm x 0.64 mm rectangular dental archwire. Is there any possibility? Constraint is that C clamp must with stand applied force (Rotation)...
05 June 2017 5,907 1 View
When we twist a bar inside a slot bar had contact on slot walls. Problem is bar is penetrating inside the wall. How to avoid. Contacts were made in Hypermesh, analysis done in ansys apdl.
08 September 2016 9,638 3 View
I did multiple load steps with ansys transient, after some time when i applied zero force, my model gives some deflection, but within elastic limit, i think that deflection (DMX) should be zero,...
08 September 2015 9,192 7 View
I wish to do loading and unloading through ansys. i able to do transient time load step but i dont know how to do reverse loading?
05 June 2015 4,854 4 View
I have ansys results of my model. I wish to know whether plastic deformation happens in the model due to force.
05 June 2015 9,400 5 View
I have a solid model imported from hypemesh. The orientation of global coordinate system is inclined (x,y,z). when I apply any force/moment it goes along the direction of coordinates not the...
06 July 2014 7,857 5 View
Time varying load step.
05 June 2014 4,337 9 View
Census data seems only to reach the year 2011, but there might be estimates somewhere that I cannot find? I am looking not only for the largest cities but also towns etc. Thanks!
10 August 2024 857 4 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...
08 August 2024 4,842 0 View
The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.
07 August 2024 9,508 1 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I'm trying to calculate the tolerance factors of the hydride perovskite and the value calculated by me and the reported values are contradictory. Need more clarity in using the correct ionic radii...
01 August 2024 2,614 1 View
How to change the displayed full article text to its corrected version? In the file on the page of the journal where I published the article, there was an error in the text, the table is...
30 July 2024 3,229 2 View
The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...
30 July 2024 3,126 0 View
Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...
29 July 2024 4,630 0 View
I have reached out to the original creator Dr. Demerouti but have had no luck with a response. I am completing my IRB form and need the information or permission by tomorrow. I know short notice,...
29 July 2024 3,684 0 View