hello FLUENT user,
please anyone tell me how to calculate amount of condensation in FLUENT?
I have done 3-D simulation (evaporation & boiling ) on FLUENT but i don't known how to calculate net amount of condensation.
Thanks
Look out in the droplet particle post processing.
Dear All, This problem from the evaporator design.We know the Inside evaporating fluid properties and temperature. Outside flowing fluid is Air. We have following unknow parameters :- 1. Air...
08 September 2018 2,320 0 View
hello everyone, I'm trying to simulate condensation model using ANSYS FLUENT. The problem domain is constant wall temperature (Tw) heat pipe and steam entering at saturation temperature(Ts). This...
03 April 2016 5,843 2 View
Hello everyone, i want to simulate a boiler pipe erosion problem in ANSYS-FLUENT. Here i'm using Discrete phase modelling. how can i set the different parameter specially in Discrete phase...
05 June 2015 9,163 0 View
hello everyone, I want to know about the measuring the blockage inside the pipe from externally. Thank you
05 June 2015 6,700 5 View
hello Fluent user, I have a problem in ANSYS FLUENT to simulate the multiphase condensation modelling with heat transfer. The problem domain is a concentric pipe with counter flow arrangement....
03 April 2015 4,707 3 View
hello, I have on energy equation in FLUENT but problem is how set input temperature of steam ? Thanks
03 April 2015 4,704 3 View
actually I have a problem to use full RAM capacity of my personal computer. fluent launcher a have set process 8 and running the simulation. I have 32 GB RAM but performance show by CPU usage...
31 December 2014 5,643 4 View
This problem (3D heat transfer problem ) energy and continuity line are not going down, they are fluctuating.what should i do .. ?
11 December 2014 1,503 2 View
i need analytic design calculation of ACSC (air cooled steam condenser).anyone have idea..??
11 December 2014 1,497 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
EMMS - Energy Minimization Multi-Scale
18 June 2024 5,857 2 View
Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...
14 June 2024 6,480 0 View
Hello, I am attempting to get condensation modelling working from a steam/CO2 multi-component gas mixture to a fluid film of water on a cold wall in Star-CCM+. The gas enter the domain above...
12 June 2024 6,095 0 View
What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?
07 June 2024 9,030 3 View