Hey, Anyone have experience in two phase condensation modelling in inclined tube using ANSYS FLUENT ?

hello everyone, I'm trying to simulate condensation model using ANSYS FLUENT. The problem domain is constant wall temperature (Tw) heat pipe and steam entering at saturation temperature(Ts). This...

03 April 2016 5,758 2 View

How can i set multi-phase simulation for heating pipe erosion problem in fluent ?

05 June 2015 9,103 0 View

How do I measure an internal blockage in a large-diameter pipe externally?

05 June 2015 6,610 5 View

How do I setup the simulation in FLUENT for multiphase condensation modelling with heat transfer through the wall ?

hello Fluent user, I have a problem in ANSYS FLUENT to simulate the multiphase condensation modelling with heat transfer. The problem domain is a concentric pipe with counter flow arrangement....

03 April 2015 4,638 3 View

How to done modelling of condensation in circular pipe by VOF method ?

03 April 2015 4,635 3 View

How do I calculate amount of condensation in FLUENT ?

02 March 2015 8,947 1 View

How do you set processes and nodes in Fluent 15 launcher?

31 December 2014 5,574 4 View

I have a problem to convergence of fluent result ?

11 December 2014 1,404 2 View

How can I calculate pressure drop across the bundle of a single row air cooled steam condenser ?

i need analytic design calculation of ACSC (air cooled steam condenser).anyone have idea..??

11 December 2014 1,426 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View