How to calculate Evaporator outiside air outlet temperature ?

Dear All, This problem from the evaporator design.We know the Inside evaporating fluid properties and temperature. Outside flowing fluid is Air. We have following unknow parameters :- 1. Air...

08 September 2018 2,240 0 View

Hey, Anyone have experience in two phase condensation modelling in inclined tube using ANSYS FLUENT ?

hello everyone, I'm trying to simulate condensation model using ANSYS FLUENT. The problem domain is constant wall temperature (Tw) heat pipe and steam entering at saturation temperature(Ts). This...

03 April 2016 5,758 2 View

How do I measure an internal blockage in a large-diameter pipe externally?

05 June 2015 6,610 5 View

How do I setup the simulation in FLUENT for multiphase condensation modelling with heat transfer through the wall ?

hello Fluent user, I have a problem in ANSYS FLUENT to simulate the multiphase condensation modelling with heat transfer. The problem domain is a concentric pipe with counter flow arrangement....

03 April 2015 4,638 3 View

How to done modelling of condensation in circular pipe by VOF method ?

03 April 2015 4,635 3 View

How do I calculate amount of condensation in FLUENT ?

02 March 2015 8,947 1 View

How do you set processes and nodes in Fluent 15 launcher?

31 December 2014 5,574 4 View

I have a problem to convergence of fluent result ?

11 December 2014 1,404 2 View

How can I calculate pressure drop across the bundle of a single row air cooled steam condenser ?

i need analytic design calculation of ACSC (air cooled steam condenser).anyone have idea..??

11 December 2014 1,426 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View