How can I find nodes with specific displacement in Odb with python?

Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?

07 August 2019 7,334 2 View

Why for a thick steel plate , Ultimate compressive strength over than "1" ?

Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...

08 September 2018 3,386 6 View

How can i delete shell element in abaqus?

I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?

04 May 2018 1,028 4 View

How can i defign and apply PBC on plate edges for compression load on other edges?

Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...

03 April 2018 4,425 7 View

What is my mistake in my tnt explosion modeling with ABAQUS?

If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...

31 December 2017 9,919 1 View

Who know about considering chapman-jouguet pressure in tnt air explosion modeling?

HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?

11 December 2017 3,842 3 View

Is Johnson cook parameter are available for ST-37 STEEL?

ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...

10 November 2017 5,991 0 View

How can I model heat and tempreature in TNT-AIR-Steel plate explicit analysis with abaqus?

I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...

07 August 2017 2,806 1 View

How can I extract a part from analysis at some step in abaqus?

Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?

06 July 2017 965 0 View

How can I remove non contact elements in a damaged part?

02 March 2017 5,289 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to calculate BREQ 3 questionnaire?

how to calculate BEHAVIOURAL REGULATION IN EXERCISE QUESTIONNAIRE BREQ 3 ,which contain 24 questions and each question has 5 answers (0- Strongly disagree , 1-disagree, 2- Neither agree nor...

02 March 2021 811 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Please suggest a good text book for "Research Methodology in Life Sciences". Which book would be good for PhD Scholars?

Please provide Book Title and author name

02 March 2021 9,059 3 View