ANY BODY HELP ME ABOUT THIS PARAMETERS:
ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...
Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?
07 August 2019 7,462 2 View
Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...
08 September 2018 3,490 6 View
I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?
04 May 2018 1,254 4 View
Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...
03 April 2018 4,532 7 View
If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...
31 December 2017 10,048 1 View
HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?
11 December 2017 3,956 3 View
I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...
07 August 2017 3,095 1 View
Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?
06 July 2017 1,076 0 View
Hi please Look at the attached pic. my part modeling damaged with some cutting holes.a few section of undamaged region is located within the void.in the meshing step,this sections create error....
02 March 2017 5,423 0 View
in my mesh,i select element delete = yes.all of plate and projectile model with shell.plate material in plastic and damage is J-C.why this reason was happened?
07 August 2016 6,682 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...
29 June 2024 6,192 2 View
Dear colleagues, I'm researching some methods of measuring the moisture of iron pellets and iron concentrate in the steel industry (especially non-contact methods). If you have any information...
22 June 2024 7,894 2 View