How can I extract a part from analysis at some step in abaqus?

07 July 2017 0 1K Report

I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?

Badges
Science topic

More Hamid Moaieri's questions See All

How can I find nodes with specific displacement in Odb with python?

Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?

07 August 2019 7,462 2 View

Why for a thick steel plate , Ultimate compressive strength over than "1" ?

Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...

08 September 2018 3,490 6 View

How can i delete shell element in abaqus?

I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?

04 May 2018 1,254 4 View

How can i defign and apply PBC on plate edges for compression load on other edges?

Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...

03 April 2018 4,532 7 View

What is my mistake in my tnt explosion modeling with ABAQUS?

If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...

31 December 2017 10,048 1 View

Who know about considering chapman-jouguet pressure in tnt air explosion modeling?

HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?

11 December 2017 3,956 3 View

Is Johnson cook parameter are available for ST-37 STEEL?

ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...

10 November 2017 6,177 0 View

How can I model heat and tempreature in TNT-AIR-Steel plate explicit analysis with abaqus?

I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...

07 August 2017 3,095 1 View

How can I remove non contact elements in a damaged part?

Hi please Look at the attached pic. my part modeling damaged with some cutting holes.a few section of undamaged region is located within the void.in the meshing step,this sections create error....

02 March 2017 5,423 0 View

Why this error in my res of modeling the imact with shell?

in my mesh,i select element delete = yes.all of plate and projectile model with shell.plate material in plastic and damage is J-C.why this reason was happened?

07 August 2016 6,682 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Strugglling with m6A dot blot any suugesstion ?

I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...

10 August 2024 8,539 5 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View