How can I find nodes with specific displacement in Odb with python?

Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?

07 August 2019 7,334 2 View

Why for a thick steel plate , Ultimate compressive strength over than "1" ?

Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...

08 September 2018 3,386 6 View

How can i delete shell element in abaqus?

I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?

04 May 2018 1,028 4 View

How can i defign and apply PBC on plate edges for compression load on other edges?

Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...

03 April 2018 4,425 7 View

What is my mistake in my tnt explosion modeling with ABAQUS?

If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...

31 December 2017 9,919 1 View

Is Johnson cook parameter are available for ST-37 STEEL?

ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...

10 November 2017 5,991 0 View

How can I model heat and tempreature in TNT-AIR-Steel plate explicit analysis with abaqus?

I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...

07 August 2017 2,806 1 View

How can I extract a part from analysis at some step in abaqus?

Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?

06 July 2017 965 0 View

How can I remove non contact elements in a damaged part?

02 March 2017 5,289 0 View

Why this error in my res of modeling the imact with shell?

in my mesh,i select element delete = yes.all of plate and projectile model with shell.plate material in plastic and damage is J-C.why this reason was happened?

07 August 2016 6,559 0 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View