If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor.
But in my model (attached) with CEL technique, this pressure is near 20 bar.
so,if you know, suggest me to correct this differences.
Dear Monyer
R U interested this fields?
Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?
07 August 2019 7,462 2 View
Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...
08 September 2018 3,490 6 View
I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?
04 May 2018 1,254 4 View
Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...
03 April 2018 4,532 7 View
HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?
11 December 2017 3,956 3 View
ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...
10 November 2017 6,177 0 View
I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...
07 August 2017 3,095 1 View
Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?
06 July 2017 1,076 0 View
Hi please Look at the attached pic. my part modeling damaged with some cutting holes.a few section of undamaged region is located within the void.in the meshing step,this sections create error....
02 March 2017 5,423 0 View
in my mesh,i select element delete = yes.all of plate and projectile model with shell.plate material in plastic and damage is J-C.why this reason was happened?
07 August 2016 6,682 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.
07 August 2024 9,508 1 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View