Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

10 August 2024 0 8K Report

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition Modeling (FDM) be used for the same purpose? How?

Badges
Science topic

Similar topics
Social Psychology
Attitude

More Orchi Datta's questions See All

How can we deal immediately with a person having anxiety attacks?

there can be some triggering situations, how do you handle them?

18 July 2024 7,076 3 View

What is the degree of crystallinity of a crosslinked polyethylene (PEX-A) pipe? Is there some kind of index? If yes, where can I find them?

I need the crystallinity percentage value of crosslinked polyethylene (PEX-A). I know that they have more than 70% crosslinking. Is there any way to calculate the crystallinity percentage from...

22 April 2024 3,007 0 View

How to check dipole-dipole interaction strength between two molecules when H bonding may not be the stabilising factor in a dimer molecule?

I have optimised the geometry of the dimer of a molecule using pcm solvent model and B3LYP functional with 6311++G(d,p) basis set in Gaussian 09 software. There is possibility of C-H...O H bonding...

01 April 2024 1,820 1 View

How to dissolve Pyrazinamide to administer in mice?

Hi, I intend to give mice 150 mg/kg of pyrazinamide. I need 3.7mg per mice and 100ul needs to be administered. The drug only dissolves in DMSO and the final amount of the DMSO in water exceeds...

27 September 2023 6,416 0 View

Without measuring lifetime, how to distinguish between fluorescence and delayed fluorescence?

The PL int will be higher in the case of Fl, but both are supposed to overlap. Then how do know if the system has delayed Fl emission?

05 September 2023 3,068 4 View

How a flame within deep tube well water in remote village can be explained as well as eliminated ?

Image Ref : The Telegraph Online ( 16.06.18 )/ 19.07.2023.

18 July 2023 397 8 View

What is the difference between PBS and Sodium Phosphate?

Sodium Phosphate manufacture uses sodium dihydrogen phosphate and disodium hydrogen phosphate. PBS manufacture uses pottasium ohosphate monobasic, sodium phosphate dibasic and sodium chloride....

03 April 2023 1,039 2 View

Is anyone using the DiameterJ Plugin to determine the fibers' diameter from SEM images?

Currently, I am trying to determine the fiber diameter in ImageJ using DiameterJ Plugin. Although I created segmented images using the diameterJ plugin, after analysis DiameterJ does not generate...

30 March 2023 9,391 6 View

Is there any solution for memory allocation problem of using SMOTE for imbalance dataset?

I am using SMOTE in a deep learning project for Minority Class Oversampling. But it costs a huge memory and Session Crash in different IDEs. Can anyone give a solution regarding to this issue?

13 March 2023 8,765 3 View

How to calculate LOD for a chemosensor based on UV-Vis studies?

A chemosensor has been developed for mercury, How to calculate the limit of detection? What equation should be used for the detection?

20 February 2023 8,400 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View