04 April 2015 3 2K Report

I don't need the ANSYS Workbench meshing User's guide. I already have it. I need the workshop and lecture file of "Introduction to ANSYS Workbench Meshing".

More Imrose Bin Muhit's questions See All
[SOLVED] Do you have the L. R. Baker's thesis, 'Flexural action of masonry structures under lateral load'?

[SOLVED] I am looking for an old thesis, which was written by L. R. Baker in 1981. I wonder anyone has the softcopy of this thesis paper? Ref: Baker, L. R. (1981). Flexural action of masonry...

07 August 2018 3,552 3 View

Which element type should analyst use for Finite Element Analysis (simulation)?

For any given Finite Element Analysis (simulation) it's essential to define each part of the geometry with one or more elements depending on the types of structures and analysis. As far as I know,...

01 February 2018 1,622 4 View

What is stochastic finite element modelling?

Stochastic finite element modelling is a widely used FEM. I want to know details about it. Can you please help me to provide some basic discussion and study material regarding stochastic finite...

08 September 2017 4,370 1 View

Research paper on numerical modeling of masonry veneer and cavity wall subjected to seismic and wind load?

Can anyone please suggest few research paper which include the numerical modeling of masonry veneer wall and cavity wall under seismic and wind load? Please don't answer if you are not sure about...

02 March 2017 8,143 1 View

Any way to download and activate ABAQUS for personal use?

I tried to download the ABAQUS v6.14 SE from from official website (3DS Academy) by using my school id. However, after downloading when I was installing, it showed that, "File is Corrupt". I check...

02 March 2017 10,190 2 View

In ABAQUS how to model wire mesh of ferrocement?

To model wire mesh of the ferrocement in ABAQUS, may I consider wire mesh same as concrete reinforcement model?

02 March 2017 5,857 6 View

What is the meaning "scale factor for the yield stress" in LS DYNA?

To define the strain rate effects in the input file of LS DYNA, we need to plot LCSR (Defined curve for Strain rate). The curve can be defined by plotting a curve  of  "Scale factor for the yield...

10 November 2015 2,887 1 View

How can I calculate energy dissipation (by porous materials like aluminum foam) from deformed volume?

Due to impact load there is a deformation in specimen and I need to calculate the energy absorbed by the specimen (aluminum foam). I have mass and velocity of the striker, deformed volume of the...

09 October 2015 6,911 4 View

What is the range of strain rate for closed cell aluminum foam where it can show significant strain rate sensitivity?

I want to know the maximum strain rate limit for closed cell aluminum foam, beyond this limit there is no strain rate effects to aluminum foam. That means, on which range of strain rate exhibits...

09 October 2015 3,645 1 View

If I submit one manuscript in two journals together, what is/are the problem(s) actually?

I am confused about one journal that, there is any chance or not to accept my paper. That's why if I want to submit one manuscript in two journals simultaneously, what is/are the problem(s)? And...

05 June 2015 7,212 2 View

Similar questions and discussions
How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Has anyone looked into the stability of FEM methods on curved meshed?

Google scholar isn't giving me any results on this

27 July 2024 595 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I decrease the error of Rietveld method for phase quantification?

Phase quantification in steel contain BCC and FCC

20 July 2024 8,150 7 View

Can someone help with the instrument configuration in Profex using Rietveld Refinement?

I am trying to configure the instrument in Profex but I can't get a chi-squared value below 9.65 for LaB6. This is the configuration of the equipment, which is a Bruker D8 Advance with a Linxeye...

14 July 2024 4,767 1 View

Anyone working in Model updating technique using FEM?

I am trying to model RCC beam with induced corrosion. How to model this beam using model updating technique.

14 July 2024 3,536 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close