[SOLVED] Do you have the L. R. Baker's thesis, 'Flexural action of masonry structures under lateral load'?

[SOLVED] I am looking for an old thesis, which was written by L. R. Baker in 1981. I wonder anyone has the softcopy of this thesis paper? Ref: Baker, L. R. (1981). Flexural action of masonry...

07 August 2018 3,343 3 View

Which element type should analyst use for Finite Element Analysis (simulation)?

For any given Finite Element Analysis (simulation) it's essential to define each part of the geometry with one or more elements depending on the types of structures and analysis. As far as I know,...

01 February 2018 1,434 4 View

Research paper on numerical modeling of masonry veneer and cavity wall subjected to seismic and wind load?

Can anyone please suggest few research paper which include the numerical modeling of masonry veneer wall and cavity wall under seismic and wind load? Please don't answer if you are not sure about...

02 March 2017 7,975 1 View

Any way to download and activate ABAQUS for personal use?

I tried to download the ABAQUS v6.14 SE from from official website (3DS Academy) by using my school id. However, after downloading when I was installing, it showed that, "File is Corrupt". I check...

02 March 2017 9,953 2 View

In ABAQUS how to model wire mesh of ferrocement?

To model wire mesh of the ferrocement in ABAQUS, may I consider wire mesh same as concrete reinforcement model?

02 March 2017 5,578 6 View

What is the meaning "scale factor for the yield stress" in LS DYNA?

10 November 2015 2,691 1 View

How can I calculate energy dissipation (by porous materials like aluminum foam) from deformed volume?

Due to impact load there is a deformation in specimen and I need to calculate the energy absorbed by the specimen (aluminum foam). I have mass and velocity of the striker, deformed volume of the...

09 October 2015 6,730 4 View

What is the range of strain rate for closed cell aluminum foam where it can show significant strain rate sensitivity?

I want to know the maximum strain rate limit for closed cell aluminum foam, beyond this limit there is no strain rate effects to aluminum foam. That means, on which range of strain rate exhibits...

09 October 2015 3,452 1 View

If I submit one manuscript in two journals together, what is/are the problem(s) actually?

I am confused about one journal that, there is any chance or not to accept my paper. That's why if I want to submit one manuscript in two journals simultaneously, what is/are the problem(s)? And...

05 June 2015 7,025 2 View

What about the quality of Journals published by University (without SCI indexed)?

There are some journals which is not SCI indexed but published from some good Universities throughout the world. I want to know the impact and quality as well as comment of specialist about those...

05 June 2015 9,324 5 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View