Can someone help me with the Johnson-Cook properties for HT9 steel?

More Hirak Basumatary's questions See All

What is the approximate cost of Whole Genome Sequencing for a eukaryotic animal at present scenario?

We are curious to learn about the approximate cost of Whole Genome Sequencing (with the highest coverage possible) for a eukaryotic animal whose genome size can be around 1.5- 2 GB. It would be...

28 November 2022 1,040 9 View

Why a set of stretched coordinates are used to solve some nonlinear equations in plasma physics, especially in fluid equations?

Can anybody help me to understand it clearly?

20 November 2022 4,361 6 View

While using the reductive perturbation method, how the stretched coordinates are chosen for various problems in a various way ?

This question is based on nonlinear dynamical system.

08 October 2022 2,562 0 View

How to get good Time-Resolved Photoluminescence(TRPL) signal of MAPbI3 thin films?

While doing TRPL of MAPbI3 thin film on corning glass substrates it is difficult to get a good intensity of emission. At best, an intensity of only about 100counts is observed with a 405nm laser...

10 October 2021 7,900 4 View

Which is the best/correct precursor for NiOx to use as HTL for perovskite solar cells?

I am looking for solution process techniques(spin coating) for depositing NiOx(Nickel Oxide) as HTL for perovskite solar cells. But I am confused in choosing a correct precursor, as I have found...

11 October 2020 1,108 4 View

How does leaching affect the soil pH in wetlands?

Is there any distinct relation between leaching process and change (increase or decrease) in soil pH, especially in wetlands?

27 August 2020 2,922 3 View

What are the methodologies for sedimentary provenance analysis?

In sedimentary provenance analysis, we use the petrographic methods, geochemistry, heavy mineral analysis, etc. I need the methodology for each technique to determine provenance. if possible then...

11 June 2020 8,732 4 View

Is the rainfall data for India at daily frequency available for free to download? Is there any site to get sediment discharge data for Indian river?

I am not connected with the server of NASA to access. I need the daily rainfall data for India from 1998-2019. To build a sediment discharge model and also for Flood inundation model for a River...

02 April 2020 9,868 0 View

What are the steps to create velocity field for flood prediction in a basin with ArcGis?

I am working to predict flood in a basin of NE India with ArcGis, but I am not able to make the velocity field for it. Give me some suggestions to do my work.

25 March 2020 7,835 3 View

Which basin can we consider for the deposition of Bomdila Group(Palaeo Proterozoic) of Eastern Himalaya?

I am looking for the Rupa dolomite and it's sedimentation history. I got about it's lithology generally but I want to know how this sediments came, where it deposited, and what might be the...

22 January 2020 5,077 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View