Are You looking for a Full ANSYS ACP tutorials?

More Armin yousefi kanani's questions See All

What is the meaning of E/Enn in traction in abaqus?

Hello Guys I know so many of you have the same question when you start using cohesive element in abaqus. This section is a bit confusing E/Enn does not mean dividing. It simply means Young modulus...

07 August 2019 7,846 4 View

Why my Load-Displacement curve from simulation is not correct?

Hello As it can be seen from below figure my simulation and experiments results are really close to each other. I just do not understand why load increases suddenly after 4 mm displacement in...

31 December 2018 4,231 0 View

How to calculate Young modulus for Flexible adhesive?

I have flexible adhesive the Maximum stress is around 2.5 MPa and strain is around 150%. When we want to calculate Young modulus for normal material we normally take values from 0.05% to 0.25%...

31 December 2018 7,959 0 View

How to calculate total load in a displacement control analysis in abaqus?

I want to plot load vs Displacement. For this I'm using the "sum" command in abaqus to add the magnitude of all the reaction forces on the fixed nodes but the load value is very low, i.e.,less...

07 August 2017 4,408 11 View

ABQUS unit system

Hello I have problem with unit system in abaqus. I have already checked tables and discussions about this subject in internet and I am confused and looking for Numerical example. Could you please...

06 July 2017 9,461 5 View

Can anyone simply explain me how can i get Cohesive zone parameters by doing experimental test?

I am currently working on adhesive joint. I want to do experimental test (DCB and ENF) to find cohesive zone information for my simulation. I am using Ansys software could anyone simply explain...

03 April 2017 817 0 View

How can I apply displacement rate (mm/time) in Ansys?

For example in tensile test displacement rate is 0.76 mm/min. My question is that how can i give exactly the same rate in ANSYS. Regards Armin

02 March 2017 3,210 0 View

Tutorial: How to model Progressive Damage on Composite Plate?

Please check my Youtube channel:

09 October 2016 2,570 1 View

Anyone familiar with buckling of simply supported laminated plates under in-plane loading?

Hello I want to analysis composite under in-plane loading. I have 2 problems 1- I could not choose proper boundary condition. When I applied boundary condition solved by R Jones my results is not...

02 March 2015 5,139 5 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Has the Affordable Connectivity Program Helped You/Your Community? And Would Bulk Tablets on a Similar Program Help Your Business?

Do You Believe VP Harris Would Show Empathy to Tech Companies in Her Administration as POTUS? I ask in light of the fact that, the ACP was not re-funded this round. So many and businesses need...

24 July 2024 4,732 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

Mahdi Haghdoust

Thank you Armin jan :) but it's not available in our country I think. Please check the link.

Best wishes

M. Haghdoust

Nawras H. Mostafa

Thanks a lot

Armin yousefi kanani

@Mahdi Haghdoust. Unfortunately due to USA sanction you cannot use udemy website from Iranian IP.

Yep! I didn't notice that. Well, as an engineer I'll find a way :)